Harman Kardon System 13828 Скачать руководство пользователя страница 22

Страница: 22 / 50

OPERATION

These indicators are the L/C/R/SL/SR/LFE letters
that are inside the center boxes of the

Speaker/Channel Input Indicators

in the

front panel

. When a standard analog stereo

or matrix surround signal is in use, only the “L”
and “R” indicators will light, as analog signals
have only left and right channels, respectively,
even surround recordings, carry surround
information on the left and right channels only.

Digital signals, however, may have one to six
separate channels, depending on the program
material, the method of transmission and the
way in which it was encoded. When a digital
signal is playing, the letters in these indicators
will light in response to the specific signal being
received. It is important to note that although
Dolby Digital, for example, is referred to as a
“5.1” system, not all Dolby Digital DVD or audio
tracks selected on DVD or other Dolby Digital
programs are encoded for 5.1. Thus, it is some-
times normal for a DVD with a Dolby Digital
soundtrack to trigger e.g. only the “L” and “R”
indicators.

The letters used by the

Speaker/Channel Input

Indicators

also flash to indicate when a

bitstream has been interrupted. This will happen
when a digital input source is selected before the
playback starts, or when a digital source such as
a DVD is put into a Pause mode. The flashing
indicators remind you that the playback has
stopped due to the absence of a digital signal
and not through any fault of the AVR. This is
normal, and the digital playback will resume
once the playback is started again.

Night Mode

A special feature of Dolby Digital is the Night
mode, which enables Dolby Digital input sources
to be played back with full digital intelligibilty
while reducing the maximum peak level and
lifting the low levels by

. This prevents

abruptly loud transitions from disturbing others
without reducing the impact of the digital source.
The Night mode is available only when Dolby
Digital mode is selected.

The Night mode may be engaged when a Dolby
Digital DVD is playing by pressing the

Night

Button

on the remote. Next, press the

buttons

to select either the middle range or

full compression versions of the Night mode. To
turn the Night mode off, press the

buttons

until the message in the lower third of the

video display and the

Main Information

Display

reads

D-RANGE OFF

The Night mode may also be selected to always be
on at either level of compression as soon as the
Dolby Digital mode is turned on using the options
in the Night Mode settings. See above for
information on using this option.

IMPORTANT NOTES ON DIGITAL PLAYBACK:

1. When the digital playback source is stopped,
or in a pause, fast forward or chapter search
mode, the digital audio data will momentarily
stop, and the channel position letters inside the

Speaker/Channel Indicators

will flash.

This is normal and does not indicate a problem
with either the AVR or the source machine. The
AVR will return to digital playback as soon as the
data is available and when the machine is in a
standard play mode.

2. Although the AVR will decode virtually all DVD
movies, CDs and HDTV sources, it is possible that
some future digital sources may not be
compatible with the AVR.

3. Note that not all digitally encoded programs
and not all audio tracks on a DVD contain full
5.1-channel audio. Consult the program guide
that accompanies the DVD to determine which
type of audio has been recorded on the disc. The
AVR will automatically sense the type of digital
surround encoding used and adjust to
accommodate it.

4. When a Dolby Digital or DTS source is playing,
you normally may not be able to select some of
the analog surround modes such as Dolby Pro
Logic II, Dolby 3 Stereo, Hall, Theater, 5CH Stereo
or Logic 7, except with special audio tracks
(see indication ”Dolby Digital” on previous page)
or data format selected (see ”PCM” on previous
page).

5. When a Dolby Digital or DTS source is playing,
it is not possible to make an analog recording
using the

Tape

Video 1

record

outputs, if the source is connected to any digital
input of the AVR only. But the analog two

channel signal of that source, the ”Downmix” to
Stereo or Dolby Surround, can be recorded by
connecting its analog audio outputs to the
appropriate analog inputs (e.g. DVD) of the AVR,
even if the digital input of the AVR remains
selected. Additionally, the digital signals will be
passed through to the

Digital Audio

Outputs

Tape Recording

In normal operation, the audio or video source
selected for listening through the AVR is sent to
the record outputs. This means that any program
you are watching or listening to may be recorded
simply by placing machines connected to the out-
puts for

Tape Outputs

Video 1 Outputs

in the record mode.

Output Level Trim Adjustment

Normal output level adjustment for the AVR is
established using the test tone, as outlined on
page 17. In some cases, however, it may be
desirable to adjust the output levels using
program material such as a test disc, or a
selection you are familiar with. Additionally, the
output level for the subwoofer can only be
adjusted using this procedure.

To adjust the output levels using program
material, first select the surround mode for which
you want to trim the speakers (see NOTE below)
by selecting the appropriate input, associated
with the desired surround mode, start your
program material source and set the reference
volume for the front left and front right channels
using the

Volume Control

Once the reference level has been set, press the

Channel Select

button

and note that

FRONT L LEVEL

will appear in the

Main

Information Display

for five seconds. To

change the level, first press the

button