Hardy HI 1734-WS Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 41

background image

Hardy 1734-WS Installation & Operation Manual

Page | 12

The base (A) mounts onto the DIN rail and provides the backplane. The
HI1734-WS POINT I/O module (B) snaps into the base. The removable
terminal block (C) also snaps into the base and provides the wiring and
terminations for field-side connections, as well as system power for the
backplane. For best performance, Hardy recommends use of 12-slot
screw-down terminal. Spring clamp blocks are only recommended
when using solid-core wiring.

To remove, simply move the Clip (D) into the downward position and
pull the HI1734-WS out of the base.

For detailed installation instructions for the POINT I/O system, please
visit:

http://literature.rockwellautomation.com/idc/groups/literature/doc
uments/sg/1734-sg001_-en-p.pdf

Load Sensor Connections

The HI 1734-WS weigh scale module will need to be connected to
external sensors, whether a single load sensor connected directly, a
group of load sensors connected through a Junction Box or a platform
scale such as a bench or floor scale connected direction. Each has its
own wiring configuration.

Below are various connections for different types of sensors and
different POINT I/O Terminal Blocks.

HI 1734-WS Weigh Scale Module Wire Terminations to Hardy Junction Boxes

SCREW DOWN TERMINALS RECOMMENDED

«
...
10
11
12
13
14
...
»

Содержание HI 1734-WS










































Отзывы:

Нет отзывов

Похожие инструкции для HI 1734-WS

Бренд: LAON TECHNOLOGY Страницы: 58

Бренд: Zazen Страницы: 8

Бренд: Nelson Страницы: 14

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 16

digital slim -1400

Бренд: Fisher Страницы: 20

Бренд: ShoreStation Страницы: 15

Бренд: Ewellix Страницы: 18

Бренд: urmet domus Страницы: 7

Бренд: Alphatech Страницы: 38

Бренд: Lightspeed Страницы: 31

Call Assistant CA48

Бренд: AT&T Страницы: 3

Бренд: PACH & COMPANY Страницы: 2

Бренд: Fermax Страницы: 16

Бренд: HIKVISION Страницы: 23

Бренд: Aiwa Страницы: 46

Бренд: Ferguson Страницы: 13

Бренд: Noblelift Страницы: 6

Бренд: Balluff Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды