Hardt INFERNO 4500 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 21

background image

HARDT

Responsive, Reliable Solutions

Page 18 of 21

CUS-009-0028-11

Gas

The installation of the gas supply must be done by a qualified plumber in accordance with local gas codes; or in the
absence of local codes in accordance with the National Fuel Gas Code; ANSI Z223.1/NFPA 54, or the Natural Gas
and Propane Installation Code; CSA B149.1, as applicable including:

•

During a pressure test of the gas supply piping system, the appliance must be completely isolated by
disconnecting the quick disconnect gas line if the test pressure is above 0.5 psi [3.5 kPa]. If the test
pressure is equal to or below 0.5 psi [3.5 kPa], only the appliances manual shutoff valve must be closed.

THE ROTISSERIE IS VERY HOT WHEN OPERATING. MAKE SURE THAT THE MAIN GAS VALVE IS
INSTALLED IN A LOCATION EASILY ACCESSIBLE TO THE EMPLOYEES.

ENSURE THE FACILITY GAS SUPPLY IS TURNED OFF BEFORE OPENING ANY CONNECTIONS PRIOR TO
OR DURING THE GAS HOSE INSTALLATION AND CONNECTION OF THE ROTISSERIE.

A RESTRAINING DEVICE MUST BE INSTALLED SUCH THAT THE ROTISSERIE MOVEMENT IS LIMITED
WITHOUT RELYING ON THE 'QUICK-DISCONNECT' HARDWARE OR ITS ASSOCIATED PIPING.

It is required that Inferno 4500 rotisseries be equipped with quick-disconnect gas/water installation
hardware.

FOR A ROTISSERIE EQUIPPED WITH CASTERS, IT IS ALSO REQUIRED THAT IT BE EQUIPPED WITH A
CONNECTOR THAT COMPLIES WITH THE STANDARD FOR CONNECTORS FOR MOVABLE GAS
APPLIANCES, ANSI Z21.69 OR CONNECTORS FOR MOVABLE GAS APPLIANCES, CAN/CSA-6.16, AND A
QUICK DISCONNECT DEVICE THAT COMPLIES WITH THE STANDARD FOR QUICK DISCONNECT DEVICES
FOR USE WITH GAS FUEL, ANSI Z21.41 (CSA 6.9).

5.4.1

Gas Pressure

Natural Gas Incoming Pressure: 7 inches W.C. [1.74 kPa] – 12 inches W.C. [2.99 kPa].
Propane Incoming Pressure: 11 inches W.C. [2.74 kPa] – 12 inches W.C. [2.99 kPa].

5.4.2

Quick Disconnect Flexible Hose

All hardware required for a quick-disconnect gas/water installation may be purchased from HARDT. The quick-
disconnect flexible hose and pipe adapter (both shown in Figure 5-5) are available from Hardt.

Figure 5-5

QUICK-DISCONNECT FITTING,
PIPE ADAPTER

QUICK-DISCONNECT
HOSE FITTING

FLEXIBLE GAS HOSE
CONNECT THIS END TO
SUPPLY

«
...
16
17
18
19
20
...
»

Содержание INFERNO 4500






















Отзывы:

Нет отзывов

Похожие инструкции для INFERNO 4500

Бренд: AcceleDent Страницы: 3

Бренд: Zero 88 Страницы: 32

Бренд: Garmin Страницы: 20

Бренд: Fast Страницы: 60

Бренд: Wayflex Страницы: 11

Бренд: ebm-papst Страницы: 10

Бренд: swamp Страницы: 5

ResQCRP ResQPUMP ACD-CPR

Бренд: Advanced Circulatory Страницы: 2

Big Wheel RN1 Series

Бренд: Osborne Страницы: 8

Бренд: Bondura Страницы: 10

Бренд: Hill-Rom Страницы: 28

Бренд: Festo Страницы: 94

Бренд: HE-VA Страницы: 48

Бренд: Zeta Страницы: 2

Бренд: Graco Страницы: 114

Бренд: MEDISTIM Страницы: 34

Бренд: Falltech Страницы: 30

Z45-D160.02 K1A

Бренд: Jäger Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды