Hardt INFERNO 4500 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 21

background image

HARDT

Responsive, Reliable Solutions

CUS-009-0028-11

Page 5 of 21

Tools & Equipment

The following tools are required to properly install the equipment:

•

A forklift or similar lifting equipment is required for proper unloading and positioning of this
equipment

•

Teflon tape

•

Crowbar

•

Claw hammer

•

Tin snips

•

Complete set of sockets with ratchet

•

Set of wrenches and/or adjustable wrenches

•

Screwdriver set

•

Measuring tape

•

Level

Warranty Information

Warranty is conditional upon proper installation as described in this document. Please note that failure to
follow these instructions can result in damage to your equipment that is not covered under warranty.

Any damage or costs incurred due to any of the following situations will not be covered.

•

Unauthorized repair by anyone other than a HARDT factory authorized service partner.

•

Installation of non-Hardt replacement or service components.

•

Alteration, misuse, or improper installation of the equipment.

•

Failure to supply water, gas, or electrical supply within Hardt approved specifications.

•

Use of unapproved cleaning materials and/or methods.

Please see your warranty document for additional details.

«
...
3
4
5
6
7
...
»

Содержание INFERNO 4500






















Отзывы:

Нет отзывов

Похожие инструкции для INFERNO 4500

Бренд: SAMCHULLY Страницы: 48

Бренд: HAGER WERKEN Страницы: 2

Бренд: M-system Страницы: 2

Бренд: Rico Страницы: 34

Бренд: Taylor Страницы: 60

Бренд: Tar River Страницы: 61

BOMAG BVP 12/50 A

Бренд: Fayat Страницы: 105

Бренд: Perel Страницы: 26

Бренд: Land Pride Страницы: 72

Бренд: Stone Страницы: 36

Бренд: Grundfos Страницы: 43

Бренд: Harken Страницы: 78

Бренд: GYM form Страницы: 40

Бренд: Atlas Copco Страницы: 10

Бренд: ION Страницы: 26

Бренд: Contec Страницы: 18

Бренд: Rompa Страницы: 5

Live Mix Pro 40-8

Бренд: DAPAudio Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды