Hamworthy Milborne 500 Series Скачать руководство пользователя | Manualshive

Страница: 43 / 64

background image

HAMWORTHY HEATING LTD

MILBORNE 500 SERIES

500001130/A

37

17.1 Control Panel Introduction:

The control panel switches give access to several functions by pressing either one of them, or a combination of
them.

RESET S1 : Press it in order to unlock the unit when a fault has occurred.

SET S2: To enter into the parameters and monitor mode of each single unit.

SET S3: Displays the running state of the different master circuits

BUTTONS S4 & S5: To increase decrease a certain value.

BUTTON S6: To store new values.

17.2 Mode Display.

The D5 red LED turns on in case a fault occurs causing the permanent lock-out of one boiler module (Reset either
the Master or the relevant boiler module to restore normal operation).

The D4 green LED displays the presence of communication between the Master and individual boiler modules.

The 3 display LED’s U2, U3 and U4 display the following;

SYSTEM STATUS

DISPLAY

No demand of heat and water
(the right digits display the flow temperature T1
e.g. T1=30°C)

Request from circuit no. 1 or from the 1st and 2nd
circuit at the same time.
(the right digits display the flow Temperature T1
e.g. T1=80°C)

Request from water circuit or simultaneous circuit
requests.
(the right digits display the Flow Temperature T1
e.g. T1=80°C)
The dot after the no. 1 left digit is flashing.

Request from no.2 circuit.
(the right digits display the Flow Temperature T1
e.g. T1=80°C)

«
...
41
42
43
44
45
...
»

Содержание Milborne 500 Series

































































Отзывы:

Нет отзывов

Похожие инструкции для Milborne 500 Series

ecoTEC plus 937

Бренд: Vaillant Страницы: 16

Бренд: Lamborghini Caloreclima Страницы: 28

Бренд: Glow-worm Страницы: 28

Caldariello Condens 25 KIS

Бренд: Riello Страницы: 55

Бренд: Lamborghini Caloreclima Страницы: 68

Бренд: Garland Страницы: 40

Henrad WH LX 30 FF

Бренд: IDEAL Страницы: 40

Бренд: Beretta Страницы: 24

Бренд: Vollrath Страницы: 6

Бренд: Qualtex Страницы: 9

Бренд: Sime Страницы: 48

Бренд: Sime Страницы: 16

Format System 25 HE

Бренд: Sime Страницы: 32

FORMAT DGT HE 12

Бренд: Sime Страницы: 32

Бренд: Southbend Страницы: 33

Бренд: Potterton Страницы: 48

Бренд: Potterton Страницы: 56

Бренд: Potterton Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды