Hamworthy Milborne 500 Series Скачать руководство пользователя | Manualshive

Страница: 39 / 64

background image

HAMWORTHY HEATING LTD

MILBORNE 500 SERIES

500001130/A

33

16.0 Master control panel error messages

The following tables display the Master board errors messages. These messages relate to faults that can occur
within the Master control panel, or from the sensors and circuits connected to the Master control panel.

Errors can be divided into two groups: lock-out errors which can be automatically reset (E errors ) and permanent
errors (A errors ) which must be reset just by pressing the reset button.

16.1 “Error” mode

The display starts flashing when a fault occurs.

Follow the procedures below to establish the fault code and its relevance.

1.

The display starts flashing to signal one or
more faults.

1b.

Press S4 (+): the display will alternate between
the address of the first unit (boiler module) and
the first error code.

Press S4 again (+) to display all the errors for
this unit (boiler module).

The error of the successive unit (boiler module)
will be visualized one after the other, press S4
(+).

Press S5 (-) to display the errors in the
opposite way, from the last to the first unit
(boiler module)

(e.g. unit [boiler module] 2 error code E 05.
Fault can be either E codes or A codes.

If errors derive from the Master, they will be
displayed (before the other errors) as U 00 +
error code. The Master controller always has
addresses U 00.

See error list for codes and

related faults

Procedures

Display

Button Required

2.

Press S2 (SET/ ESC) to exit ‘errors’ and go
back to display mode.

«
...
37
38
39
40
41
...
»

Содержание Milborne 500 Series

































































Отзывы:

Нет отзывов

Похожие инструкции для Milborne 500 Series

Бренд: hajdu Страницы: 6

Бренд: IBC Страницы: 4

Бренд: IBC Страницы: 6

Бренд: IBC Страницы: 74

Vela X N 24 MB/IT

Бренд: Lamborghini Caloreclima Страницы: 30

EnviroPlus F24e

Бренд: Saunier Duval Страницы: 64

Бренд: Immergas Страницы: 96

MURELLE HE 25-55 ErP

Бренд: Sime Страницы: 104

Бренд: Baxi Страницы: 16

PREMIER PLUS 400

Бренд: Baxi Страницы: 16

PREMIER PLUS 1000L

Бренд: Baxi Страницы: 20

Supermaster 23 e

Бренд: Hermann Страницы: 48

Бренд: CR Remeha Страницы: 110

Бренд: TRIFIRE Страницы: 56

Caldaria 100.2 Condensing+ export

Бренд: Robur Страницы: 56

Бренд: Unical Страницы: 44

Prestige Solo 399

Бренд: TriangleTube Страницы: 12

Бренд: Gabarron Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды