Hamworthy Milborne 500 Series Скачать руководство пользователя

Страница: 52 / 64

HAMWORTHY HEATING LTD

MILBORNE 500 SERIES

500001130/A

No Desc. Lower

Limit

Family Upper

Limit

Default

Value

Note Specification Pc

Screen

44 T_CH_

High_

max

10°C Rh 117°C 90 Safety

Device

If T1 > T1 maximum temperature for
5 seconds. It limits the fan speed,
parameter 15

CH_

high

45 P-factor

CH_high

255

P-factor for PI-control in CH-high
mode

CH_

high

46 I-factor

CH_high

255

I-factor for PI-control in CH-high
mode

CH_

high

47 D-factor

_CH_

high

0 Rh 255 128

D-factor

for

PI-control

CH-high

mode

CH_

high

48 CH_high

Blocking

_time

0 sec

255 (=

minutes)

0 Time

before re-
start in CH
mode after
a
thermostat
opens

After the burner is switched off in
CH-mode the system is blocked
for CH-mode for this blocking
time

CH_

high

49 Post

pump

time

CH_high

0 (=

minute

Rh 255

(cont.

functioning

5 Pump

over-run
high temp
circuit

This is the post pump time after
the high temperature heating
circuit room thermostat opens

CH_

high

50 T_high

correctio

n 20°C

-30°C

30°C

Calibration / correction of the
high temp sensor lower limit at
20°C

CH_

high

51 T_high

correctio

n 85°C

-30°C

30°C

Calibration / correction of the
high temp sensor upper limit at
85°C

CH_

high

52 Blocking

time

DHW>

0 =

switch

with

burner

1= 1

minute

Rh 255

minutes)

0 Delayed

change-
over from
DHW
mode to
CH mode

Duration of burner off period when
changing from DHW mode to CH
mode.
0 = Seamless change, burner stays
on
1 = Delayed change, burner off = 1
min
2 = etc.

CH_

high

53 T_CH_

Low_

max

10°C Rb 90°C 80 Safety

device

If T1 > T1 maximum temperature
for 5 seconds. This value is
always <= T_CH_High_max
parameter 44. It limits the
parameter 21.

CH_

low

54 P-factor

CH_low

0 Rb 255 30

P-factor for PI-control in CH-low
mode

CH_

low

Heating Engineers Parameter List (Cont’d)

2nd Level Password (on the Master and on the computer.

Содержание Milborne 500 Series

































































Результаты поиска

Содержание Milborne 500 Series

Отзывы:

Похожие инструкции для Milborne 500 Series

Бренды по названию

Популярные бренды

Hamworthy Milborne 500 Series, Руководство по проектированию, монтажу, пусконаладке и эксплуатации

Результаты поиска

Содержание Milborne 500 Series

Отзывы:

Похожие инструкции для Milborne 500 Series

Бренды по названию

Популярные бренды