HAMAR LASER L-705 Скачать руководство пользователя страница 29

Страница: 29 / 30

Configuring the R-1307 Readout for the A-1519-2.4ZB Wireless

Target in Dual-Axis Mode

Press and hold the

Menu

button until the menu displays.

Press and release the

Menu

button until

displays in both the V and H Display windows.

Use the up or down arrow keys to set the

Vertical ID

to 01.

Press the

Menu

button again and use the up or down arrow keys to set the

Horizontal ID

to 01.

Press the

Menu

button again and use the up or down arrow

keys to set the

Channel



Note:

Ensure that the Target System ID dial on the side of the

target is set to 1.

Press the

Menu

button until



displays in the Vertical Display window. Use the up or down

arrow keys until



displays in the Horizontal Display window. After a few seconds the R-1307

readout will start polling for the target. When the laser beam is on the target, readings display in the

Vertical and Horizontal Display windows.

Press and hold the

arrow key to zero the readout.

Take measurements in each bore as described in

Measuring Bores with the A-1511 Wand Bore

Target and the R-1307 Readout

beginning on Page 19.

Note:

When using the Wand Bore Fixture with the R-1307 Readout, adjust the support leg until the horizontal

readings are less than .030 in. (.73 mm).

Содержание L-705































Результаты поиска

Содержание L-705

Отзывы:

Похожие инструкции для L-705

Бренды по названию

Популярные бренды

HAMAR LASER L-705, Руководство по эксплуатации

Результаты поиска

Содержание L-705

Отзывы:

Похожие инструкции для L-705

Бренды по названию

Популярные бренды