Haier FlexFit Pro AL24LP2VHA, Руководство по обслуживанию

Страница: 117 / 121

113
FlexFit Pro
ENGLISH
SE
CTION E
NOTE: The display backlight must be illumi-
nated before proceeding. To turn the back-
light on, press any key (MODE, FAN,  ,
TIME, or SET) located at the bottom of the
display, or press the ON/OFF key located at
the top of the display.
Timer ON
Press the TIMER key once, the ON timer icon will appear in the
upper right corner of the screen. The ON icon and hour posi-
 keys to set the hour. Press
the TIMER key again, the ON icon and minutes position are

keys to set the minutes. Press the
Timer OFF
Press the TIMER key 3 times, the OFF timer icon will appear in
the upper right corner of the screen. The OFF icon and hour

keys to set the hour.
Press the TIMER key again, the OFF icon and minutes position
 keys to set the minutes. Press
Timer ON/OFF
Press the TIMER key 5 times, the ON/OFF timer icon will ap-
pear in the upper right corner of the screen. The ON icon and
 keys to set the hour.
Press the TIMER key again, the ON icon and minutes position
 keys to set the minutes. Press
the TIMER key again, the OFF icon and hour position are now

keys to set the hour. Press the TIMER
Press the

keys to set the minutes. Press the SET key to
ON) and adjusts the arrow direction accordingly.
If neither

key is pressed within 10 seconds, or if the
MODE, FAN, or ON/OFF keys are pressed prior to pressing the
SET key, the setting function is canceled and reverts back to
the previous setting.
Timer Cancel
Press the TIME key up to 9 times to cycle through the timer
settings. When the timer icon disappears, the timer function is
canceled.
Note: An active timer function will remain displayed on screen
until the set time has been reached and command completed.
Timer Function Setting
WIRED CONTROLLER OPERATION
Settings & Functions
Press the SET key. The swing louver function icon will
be displayed. Press the

keys to advance through
the functions to select ECO function. (The icon will
icon will remain on.
To cancel ECO function, repeat the above steps.
NOTE: The energy saving default parameters are listed below:
74°F Lowest temperature limit of Cooling and Dry mode.
78°F Highest temperature limit of Heating mode.
74°F – 86°F Temperature adjustment range in Cooling and Dry
mode.
60°F – 78°F Temperature adjustment range in Heating mode.
ECO
For Cooling
Under Cooling mode, set the temperature to 86°F. Press and
hold the FAN key for 5 seconds. The Cooling ECO param-
screen. Default temperature is 74°F. Press the

keys to
adjust the lowest target cooling temperature. Press the SET
For Heating
Under Heating mode, set the temperature to 60°F. Press and
hold the FAN key for 5 seconds. The Heating ECO parameter
screen. Default temperature is 78°F. Press the  keys to
adjust the highest target heating temperature. Press the SET
Press and hold the SET and FAN keys for 5 seconds. The cur-
rent static pressure will be displayed in the upper right corner
Press the TIME key to shift the unit no. displayed in the upper
left corner of the screen. The unit numbers are from 00-15.
Press the  keys to change the static pressure grade,
shown in the upper right corner of the screen.
setting. Press the MODE, FAN, or ON/OFF key to exit the
function. If no key is pressed in 10 seconds, the function will
also exit.
NOTE: This function requires the ON/OFF key LED to be
turned ON and the screen backlight to be illuminated.
NOTE: This function requires the ON/OFF key LED to be
turned ON and the screen backlight to be illuminated.
NOTE: This function requires the ON/OFF key LED to be
turned ON and the screen backlight to be illuminated.
ECO Energy Saving Function
ECO Parameter Setting
Static Pressure Grade Inquiry & Adjustment