GW Instek COM-804 Скачать руководство пользователя страница 85

Страница: 85 / 157

GOM-804 & GOM-805 User Manual

3. Channel
setting

The Channel setting sets the number of DUT channels

that are used.
Use the arrow keys to navigate to the Channel setting and
press Enter.

Use the left and right arrow keys to select a digit. Use the

up and down arrow keys to edit the value of the selected
digit. Press Enter to confirm the setting.

Channel setting

Move

and edit

Select and

confirm

Enter

Channel Range: 01 ~100

4. Delay setting

The Delay setting adds a pause between each channel
measurement.
The Use the arrow keys to navigate to the Delay setting
and press Enter.

Use the left and right arrow keys to select a digit. Use the
up and down arrow keys to edit the value of the selected

digit. Press Enter to confirm the setting.

Delay setting

Move

and edit

Select and

confirm

Enter

Delay Range:

400ms ~ 30000ms

5. Start the scan.

Press the

Trigger

key or input a pulse signal on the

Trigger pin of the SCAN interface port to start a scan
test.

Note

See page 64 to set the external trigger edge as a rising or
falling leading edge.

The results will be displayed on the screen as each test is

performed. The results will also be output through the
scan port until the scan has finished.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание COM-804






























































































































































Результаты поиска

Содержание COM-804

Отзывы:

Похожие инструкции для COM-804

Бренды по названию

Популярные бренды

GW Instek COM-804, Руководство пользователя

Результаты поиска

Содержание COM-804

Отзывы:

Похожие инструкции для COM-804

Бренды по названию

Популярные бренды