GW Instek COM-804 Скачать руководство пользователя страница 59

Страница: 59 / 157

GOM-804 & GOM-805 User Manual

Measurement Settings

Background

The following measurement settings are used to
configure the various measurement modes.

Average Function

Background

The average function smoothes measurements using a
moving average. The average function sets the number of

samples used for the moving average; a higher number
results in smoother measurement results. The average

function is turned off by default.

1. Select Average
setting

From one of the main screens, press
the

ESC

key so that the menu

system at the bottom of the display
has focus.
Go to Meas. Setup and press Enter.
Go to Average and press Enter.

Meas. Setup

menu icon

Move

Select menu

or setting

Enter

2. Average
setting appears

Use the arrow keys to turn Average on and set the
average number. Press Enter to confirm the setting.

Average settings

Average

OFF, ON: 2~10

Note

Pressing ESC before pressing ENTER will exit the Average
function settings.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание COM-804






























































































































































Результаты поиска

Содержание COM-804

Отзывы:

Похожие инструкции для COM-804

Бренды по названию

Популярные бренды

GW Instek COM-804, Руководство пользователя

Результаты поиска

Содержание COM-804

Отзывы:

Похожие инструкции для COM-804

Бренды по названию

Популярные бренды