GW Instek COM-804 Скачать руководство пользователя страница 64

Страница: 64 / 157

MEASUREMENT

Temperature Unit

Background

Temperature units can be set to Fahrenheit or Celsius for
all temperature measurements.

1. Select
Temperature Unit
setting

From one of the main screens, press
the

ESC

key so that the menu

system at the bottom of the display

has focus.
Go to Meas. Setup and press Enter.
Go to Temperature Unit and press
Enter.

Meas. Setup

menu icon

Move

Select menu

or setting

Enter

2.Temperature
Unit setting
appears

Use the arrow keys to set the Temperature Unit. Press
Enter to confirm the setting.

Temperature

Unit

Temperature Unit Fahrenheit, Celsius

Note

Pressing ESC before pressing ENTER will exit the
Temperature Unit setting.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание COM-804






























































































































































Результаты поиска

Содержание COM-804

Отзывы:

Похожие инструкции для COM-804

Бренды по названию

Популярные бренды

GW Instek COM-804, Руководство пользователя

Результаты поиска

Содержание COM-804

Отзывы:

Похожие инструкции для COM-804

Бренды по названию

Популярные бренды