GVS KI/U 0401.1 Скачать руководство пользователя страница 36

Страница: 36 / 53

K-BUS

KNX/EIB

Universal Interfaces

Parameter “Connect contact type”

This parameter defines whether the contact at the input is a normally open contact or a normally

closed contact.Options:

Normally closed

Normally open

The parameter introduced in this chapter is use “Normally open” as the example, the normally close

is just opposite.

Parameter “Operation functionality type”

This parameter defines the types of the shutters operation, detailed description of the type and

function as the following table:

1-push-button,short=stepping, long=moving

Short operation

Alternate implement “Stop/Adjust upward” or “Stop/Adjust downward”
operation

（

alternate send the value of the object “0”and“1”

）

Long operation

Alternate implement “Move up” or “Move down” operation

（

alternate send the value of the object “0”and“1”

）

1-push-button, short=moving, long=stepping

Short operation

Alternate implement “Move up” or “Move down” operation

（

alternate send the value of the object “0”and“1”

）

Long operation

Alternate implement “Stop/Adjust upward” or “Stop/Adjust downward”
operation

（

alternate send the value of the object “0”and“1”

）

1-push-button-operation, moving

Operation

When operation

，

send the command in sequence

：

……

－

>Move up

－

>Stop/Adjust upward

－

>Move down

－

>Stop/Adjust

downward

－

>……

1-switch-operation, moving

Operation start

（

press the button

）

Alternate implement “Move up” or “Move down” operation

（

alternate send the value of the object “0”and“1”

）

Operation end

（

Release the button

）

Stop/Adjust

2-push-button, standard

Short operation

“Stop/Adjust upward” or “Stop/Adjust downward”

（

set by parameter

）

Long operation

“Move up” or “Move down”

（

set by parameter

）

Содержание KI/U 0401.1






















































Результаты поиска

Содержание KI/U 0401.1

Отзывы:

GVS KI/U 0401.1, Руководство пользователя, Страница: 36 / 53

Результаты поиска

Содержание KI/U 0401.1

Отзывы: