manualshive.com logo in svg

GVS KI/U 0401.1, Руководство пользователя, Страница: 15 / 53

Поделиться
Скачать
GVS KI/U 0401.1 Скачать руководство пользователя страница 15

K-BUS

®

KNX/EIB

Universal Interfaces

12

5.1.3. Parameter window “Switch/dimming, X”

Parameter window “Switch/dimming, X” will be shown in Fig. 5, it is visible when Function of the

channel “Switch/Dimming” is selected. The function enables the operation of dimmable lighting. 1 button
operation is also possible.

Fig. 5 Parameter window “Switch/Dimming”

Parameter “Connect contact type”

This parameter defines whether the contact at the input is a normally open contact or a normally

closed contact.Options:

Normally closed

Normally open

The parameter introduced in this chapter is use “Normally open” as the example, the normally close

is just opposite.

Parameter “Dimming functionality”

This parameter determines whether the lighting is only dimmed or whether it should also be

switched.Options:

Dimming and switching

Only dimming

If the parameter “Only dimming” is selected, there is no distinction between a short and long

operation. The dimming command is therefore carried out immediately after the push button action; there
is no delay to determine whether the operation is long or short. If the parameter “Dimming and switching”

Содержание KI/U 0401.1






















































Отзывы:

Нет отзывов