Gude Expert Power Control 8021 Series Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 98

background image

22

Expert Power Control 8021/8025

© 2021 GUDE Systems GmbH

Operating

3) by Software: (only if "Enable FW to BL" was previously activated in the
"GBL_Conf.exe" application)

·

Start the "GBL_Conf.exe" program

·

Do a network search with the "Search" menu action

·

Activate in menu "Program Device" the item "Enter Bootloader"

4) via web interface:

Press "Enter Bootloader Mode" on the maintenance

web page.

Whether the device is in Bootloader mode, is indicated by the flashing of the status
LED, or it is shown in "GBL_Conf.exe" application after a renewed device search (ap-
pendix "BOOT-LDR" after the device name). In Bootloader mode the program
"GBL_Conf.exe" can disable the password and the IP ACL, perform a firmware update,
and restore the factory settings.

For devices with relays, entering or exiting the bootloader mode does not change

the state of the relays as long as the operating voltage is maintained.

Abandonment of the Bootloader Mode

1) via push button:

·

Hold both buttons for 3 seconds (only if the device has 2 buttons)

2) or

·

Remove and connect the power supply without operating a button

3) by Software:

·

Start the "GBL_Conf.exe" application

·

Do a network search with the "Search" menu action

·

In menu

"

Program Device

"

activate the item "Enter Firmware"

Factory Reset

If the device is in bootloader mode, it can always be put back to its factory default. All
TCP/IP settings are reset in this operation.

If a unit is set to factory defaults, an uploaded certificate or updated firmware will

be preserved.

1) via push button:

·

Activate the Bootloader Mode of the device

·

Hold down the button (or the "Select" button for devices with 2 buttons) for 6
seconds. If the push button is recessed, use a pin or paper clip

·

The status LED will blink in a fast rhythm, please wait until the LED blinks slowly
(about 5 seconds)

2) by Software:

·

Activate the Bootloader Mode of the device

·

"Start the GBL_Conf.exe" program

·

In menu "Program Device

"

activate the item

"Reset to Fab Settings"

19

«
...
20
21
22
23
24
...
»

Содержание Expert Power Control 8021 Series



































































































Отзывы:

Нет отзывов

Похожие инструкции для Expert Power Control 8021 Series

Бренд: Eaton Страницы: 12

Бренд: FELA Страницы: 13

DynaGST/2402G GEP-33224T-1

Бренд: UNICOM Страницы: 1

Cleveland Controls RSS-498-013

Бренд: UNICONTROL Electronic Страницы: 2

Бренд: D-Link Страницы: 17

Бренд: Techroutes Страницы: 22

Бренд: Black Box Страницы: 2

SRS Lighting DTS16F-DIN

Бренд: plasa Страницы: 4

CEFLA PIR DALIP

Бренд: DANLERS Страницы: 2

Бренд: Clas Ohlson Страницы: 5

OpenGear DSS-8224

Бренд: Ross Страницы: 47

Бренд: ABM Страницы: 8

Smart-Switch/801 FEP-30109T-C

Бренд: UNICOM Страницы: 22

Бренд: STI Страницы: 2

Бренд: Rackmount Страницы: 16

Бренд: Exsys Страницы: 14

SENSALINK SENLSS V2

Бренд: Thorn Страницы: 2

LANPLEX 2500 EXTENDEDPLEX 2500 EXTENDED

Бренд: 3Com Страницы: 186

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды