Gude Expert Power Control 8021 Series Скачать руководство пользователя страница 32

Страница: 32 / 98

Expert Power Control 8021/8025

Configuration

3.3.1

Console

Telnet

Enable Telnet: Enables the Telnet console.

Telnet TCP port: Telnet sessions are accepted on this port.

Raw mode: The VT100 editing and the IAC protocol are disabled.

Active negotiation: The IAC negotiation is initiated by the server.

Activate echo: The Telnet echo setting if not changed by IAC.

Push messages: Sends push messages via SSH.

Delay after 3 failed logins: After 3 wrong entries of username or password, the next lo-
gin attempt is delayed.

SSH

Enable SSH: Enables the SSH protocol.

Содержание Expert Power Control 8021 Series



































































































Результаты поиска

Содержание Expert Power Control 8021 Series

Отзывы:

Похожие инструкции для Expert Power Control 8021 Series

Бренды по названию

Популярные бренды

Gude Expert Power Control 8021 Series, Руководство пользователя

Результаты поиска

Содержание Expert Power Control 8021 Series

Отзывы:

Похожие инструкции для Expert Power Control 8021 Series

Бренды по названию

Популярные бренды