Gude Expert Power Control 8021 Series Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 98

background image

91

Expert Power Control 8021/8025

© 2021 GUDE Systems GmbH

Specifications

E-Mail messages

E-Mail messages are triggered by the following events:

·

Turning on the device

·

Switching of the Power Ports

·

Loss / return of voltage

·

Exceeding of the max / min values of attached sensors

·

State change of digital sensor input ports

·

Exceeding of max / min values of the measured power consumption

·

Condition change of overvoltage protection

SNMP Traps

SNMP Traps are system messages that are sent via the SNMP protocol to different re-
cipients. SNMP traps are triggered by the following events:

·

Switching of the Power Ports

·

Exceeding of the max / min values of attached sensors

·

State change of digital sensor input ports

·

Exceeding of max / min values of the measured power consumption

·

Condition change of overvoltage protection

Syslog messages

Syslog messages are simple text messages that are sent via UDP to a syslog server.
Under Linux, normally a syslog daemon is already running (eg. syslog-ng), for Mi-
crosoft Windows systems some freeware programs are available on the market. The
syslog messages are sent for the following events:

·

Turning on the device

·

Enable/disable of syslog in the configuration

·

Switching of the Power Ports

·

Loss / return of voltage

·

Exceeding of the max / min values of attached sensors

·

State change of digital sensor input ports

·

Exceeding of max / min values of the measured power consumption

·

Condition change of overvoltage protection

«
...
89
90
91
92
93
...
»

Содержание Expert Power Control 8021 Series



































































































Отзывы:

Нет отзывов

Похожие инструкции для Expert Power Control 8021 Series

Бренд: D-Link Страницы: 2

Бренд: B&K Страницы: 2

Бренд: B&B Electronics Страницы: 45

Бренд: Gavita Страницы: 12

3CR17251-91 - Switch 5500G-EI Stackable Gigabit...

Бренд: 3Com Страницы: 148

Бренд: Cabletron Systems Страницы: 110

Бренд: Delta Electronics Страницы: 1

Бренд: Hanwell Страницы: 109

Бренд: Olympia Страницы: 6

tekmarNet4 User Switch 480

Бренд: Tekmar Страницы: 8

Бренд: Ruby Tech Страницы: 254

Бренд: Advantech Страницы: 101

Бренд: Linkskey Страницы: 2

CT-HDVD-4X14K-SW

Бренд: NB Страницы: 23

Бренд: Marmitek Страницы: 32

SUPERHUB QUATTRO

Бренд: Manhattan Страницы: 2

SW-HDM3D-C5-8X8

Бренд: Avenview Страницы: 20

Бренд: Novus Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды