GTO SW-4000XL Скачать руководство пользователя | Manualshive

Страница: 31 / 44

background image

27

Learn Remote

Button

1

2

3

4

O

N

D

IP

STATUS

LEARN RMT

LEARN

MAST LIMIT

LEARN

SLV LIMIT

S3

S4

S2

ART OFF
G OFF

PULL

EN DLY.

OFF
OFF

ON
ON
PUSH
SIMULT.
ON
ON

120 MIN

MAX

CLOSE TIME

STALL FORCE

3. “Teach” the New Code to Control Board Memory

A. Press and hold transmitter button.
B. Press and hold the

LEARN RMT (Learn Remote)

button

on the control board until the buzzer sounds.

C. Release transmitter button. The new code
is stored in control board memory.
D. Release the

LEARN RMT (Learn Remote)

button.

Setting Your Personal Transmitter Code

All GTO transmitters are set to a standard code at the factory and are ready to operate your GTO PRO® Gate Opener

®

. For

your safety and security, however, we

strongly recommend

that you replace the factory setting with your own personal code.

Follow the directions below:

TESTING YOUR CLOSED LIMIT SETTING:

Press your entry transmitter and allow your gates to close. If CLOSED positions are not correct or need to be changed, you
will need to CLEAR your CLOSED LIMIT settings and follow Steps 1-7 again.

CLEARING PROGRAMMED CLOSED LIMIT SETTING:

If you make a mistake and set the limit at the wrong position – press your transmitter to return the gates to their fully opened

positions, then press and hold the 'LEARN MAST LIMIT' or 'LEARN SLV LIMIT' button for 5 seconds. This will clear the

memory for the closed limit positions. Follow Steps 1-7 again.

2. Set the transmitter DIP Switches

There are nine (9) transmitter DIP switches; each can be placed in three different
positions (

+

,

0

,

–

).

DO NOT

set all the switches in the same position, such as all

+

,

all

0

, or all

–

. Once the DIP switches have been set to a personal code, replace front

cover.

WARNING: No other adjustments should be made inside the transmitter.

1. Remove the Transmitter Cover

On the back of the transmitter use a small phillips head screw driver to remove
the two screws on the sides of the visor clip and separate the front cover from the
transmitter. With the front cover removed, the battery and the DIP switches will
be exposed. To set a new code, use a small screwdriver to move the switches.

+

0

ECE

1 2 3 4 5 6 7 8 9

1

2

3

4

5

6

7

8

9

ECE

A23S 12V

ALK

ALIN

E B

ATT

ER

Y

+

0

–

LED

«
...
29
30
31
32
33
...
»

Содержание SW-4000XL













































Отзывы:

Нет отзывов

Похожие инструкции для SW-4000XL

Бренд: Samson Страницы: 100

Бренд: Radio Shack Страницы: 3

Бренд: UE Страницы: 4

Бренд: Quectel Страницы: 23

Бренд: Quectel Страницы: 79

Бренд: Canarm Страницы: 3

Бренд: B&R Industries Страницы: 89

sensoCOMFORT VRC 720/3

Бренд: Vaillant Страницы: 64

Бренд: Elby Designs Страницы: 4

MagicSpeed Series

Бренд: Waeco Страницы: 76

Бренд: Brand Innovations Страницы: 56

Бренд: PS Automation Страницы: 4

Бренд: Barco Страницы: 4

Бренд: Blue Point Engineering Страницы: 12

Бренд: Raypak Страницы: 2

Бренд: 4D systems Страницы: 6

Бренд: Phoenic Mecano Страницы: 5

DIGI-STAR GT400

Бренд: AGRI TRONIX Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды