manualshive.com logo in svg

GTO SW-4000XL, Руководство по установке

Поделиться
Скачать
GTO SW-4000XL Скачать руководство пользователя страница 42

38

Column Installation Information 

I

F THIS OPERATOR WILL BE USED WITH GATES THAT ARE MOUNTED ON  

MASONRY, BRICK, OR ROCK (etc.) COLUMNS:

READ THE FOLLOWING CAREFULLY BEFORE PROCEEDING

A.   

The simplest solution is to install  the operator in a push-to-open configuration. The minimum clearance is easier 
to achieve and clearance is no longer a problem, since the operator will be pushing the gate away from the column 
instead of pulling it toward the column.  It is recommended that you place a steel plate between the operator 
mounting brackets and masonry surface for additional strength.

B.   

If a push-to-open installation is impossible due to traffic hazards, terrain, etc., another option is to re-hang the gate.  
You may hang it on a post, either in the center of the column or at the back corner, or move the gate to the back 
corner of the columns.

C.   

The most difficult solution is to cut a notch in the column to accommodate the operator and power cable.  This job is 

NOT

 for the inexperienced!

Column

Pivot Bracket

Gate

A

B

Column Mount Example 
(A + B can not exceed 19 inches)
Example:  If A is 2" then B can not exceed 17"

Hinge

Содержание SW-4000XL













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды