manualshive.com logo in svg

GTO SW-4000XL, Руководство по установке

Поделиться
Скачать
GTO SW-4000XL Скачать руководство пользователя страница 43

39

ACCESSORIES

®

DC-SERIES

®

DC-SERIES

AUT

OMA

TIC 

GAT

E LO

CK

Solar Panel (FM123), (FM122)

 

The 

Solar Panel

 is a 10 watt solar powered battery charger for use with the 

all GTO/PRO DC 

gate 

operator systems. Particularly suited for remote installations, each 

Solar Panel

 comes with tubular 

steel support, mounting clips, wire connectors, and 8 ft. of low voltage wire (see Low Voltage Wire 
for additional wire). The 

GTO/PRO® 

control board has clearly labeled terminal connections for easy 

installation of the 

Solar Panel

.  Installation in some regions of the world will require multiple solar 

panels for adequate charging power. 

Solar Panel (FM122) 

is a 5 watt solar powered battery 

charger with all the same features as (FM123).

Push Button Control (RB101)

Unlit doorbell button for remote entry or exit control. Wires directly to the control board and uses 16 
gauge multi-stranded, dual conductor low voltage wire (sold separately).

Pin Lock  (FM345)

The 

Pin Lock

 substitutes for the clevis pin at the front end of the 

GTO/PRO®

 gate operator. Helps 

prevent theft of the operator from the gate, while allowing quick release of the operator.

Key Chain Two Button Transmitter (RB742)

The Key Chain Mini Transmitter is a miniature version of the 

GTO/PRO®

 entry transmitter and has 

the same adjustable code settings. 12 Volt battery included. 

Single Button Transmitter (RB741) 

The 

GTO/PRO® 

entry transmitter, with adjustable code settings, is standard equipment with all 

GTO/PRO® 

systems. 12 Volt battery included. 

Digital Keypad (F310)

The specially designed digital keypad can be easily installed as a wireless or wired keypad. It can be 
programmed to use up to 25 different personal identification number (PIN) codes. Each code is face 
programmable with additional security features built in. Wired installations require 16 gauge, low 
voltage, multi-stranded, dual conductor, direct burial wire (sold separately).  Requires 3 AA batteries 
(not included).

Mounting Post (F100) - In Ground

This black powder coated pedestal is designed to provide convenient access to your keypad, wireless 
intercom, or other access control device from your vehicle. With its break down design it is easy to 
install and works well in most standard applications. Surface Mount Flanges (F102) and Extensions 
(F103) for added height are available.

GTO/PRO 50' Exit Wand (FM139), 100' Exit Wand (FM140), 150' Exit Wand (FM141) 

The 

GTO/PRO®

 Exit Wand is designed for residential and agricultural applications and is 

compatible with all 

GTO/PRO®

 automatic gate operator models. The wand is an electromagnetic 

sensor, which offers 'hands free' operation of the 

GTO/PRO®

 Gate Operators with a 12 ft. radius of 

detection of vehicles in motion.

Automatic Gate Lock Pull-to-Open (FM144) 

A

 

MUST for added security. Solenoid driven, with a steel housing. Unlocks and locks automatically 

as gates open and close. Used with 

GTO/PRO® 

DC swing gate operating systems for maximum 

stability and security. Comes with a keyed manual release. Recommended for gates over 8 ft. long. 
Ideal for animal enclosures or high wind areas.

1

2

3

4

5

6

7

8

9

0

Содержание SW-4000XL













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды