GTO SW-4000XL Скачать руководство пользователя

Страница: 11 / 44

IMPORTANT SAFETY INSTRUCTIONS

Warning signs (4 enclosed) to be installed on each side
of the gate (3–5 feet above the bottom of the gate).

Maximum Gate: 1000 lb. (453.5 kg); 20 ft. (6.1 m)
Voltage: 12 Vdc; Frequency: 0 Hz; Power: 60 W
Class I, II, III and IV Vehicular Swing Gate Operator.
Serial Number: XXXXXXXXXX

#xxxxxxx

Conforms to UL 325 STANDARDS

TO MANUALLY OPEN AND CLOSE THE GATE:

1. Turn control box power switch OFF.
2. Disconnect front or rear mount from gate bracket.
3. Pull operator away from front or real mounts.

DC SW-4000XL SERIES

GTO, Inc.

Tallahassee, Florida USA

Disconnect operator ONLY when the control box power
switch is OFF and the gate is NOT moving.

LISTED

Product identification and manual operation instruction
label (1) installed on control box.

Logo and warning labels (2) installed on each side of master operator housing.

1. KEEP CLEAR! Gate may move at any time.

2. Do not allow children to operate gate or play in

gate area.

3. This gate is for vehicles only. Pedestrians must

use separate entrance.

WARNING

MOVING GATE

Can Cause Injury or Death

Logo and warning labels (2) installed on each side of slave operator housing.

1. KEEP CLEAR! Gate may move at any time.

2. Do not allow children to operate gate or play in

gate area.

3. This gate is for vehicles only. Pedestrians must

use separate entrance.

WARNING

MOVING GATE

Can Cause Injury or Death

1-800-543-GA

TE (4283) • www

.gtopro.com

These warning labels should be found

at the locations specified below.

If any of them are missing,

immediately contact GTO for

replacements.

Содержание SW-4000XL













































Результаты поиска

Содержание SW-4000XL

Отзывы:

Похожие инструкции для SW-4000XL

Бренды по названию

Популярные бренды

GTO SW-4000XL, Руководство по установке

Результаты поиска

Содержание SW-4000XL

Отзывы:

Похожие инструкции для SW-4000XL

Бренды по названию

Популярные бренды