GTO SW-4000XL Скачать руководство пользователя страница 3

Страница: 3 / 44

Gate Operator Class Categories ------------------------------------------------------------inside cover
Units and Standards Conversion Chart ---------------------------------------------------inside cover

PLEASE READ THIS FIRST! --------------------------------------------------

page iii

Important Safety Instructions --------------------------------------------------

page 1

Disconnecting the Operator -----------------------------------------------------------page 1

Important Safety Instructions for the Consumer ------------------------------------page 2

Secondary Means of Protection Against Entrapment ------------------------------page 5

Required Safety Precautions for Gates -----------------------------------------------page 6

Warning Signs and Labels -------------------------------------------------------------page 7

Installation --------------------------------------------------------------------------

page 8

Parts List ---------------------------------------------------------------------------------page 8

Technical Specifications -------------------------------------------------------------page 11

Installation Overview ------------------------------------------------------------------page 12

Installing the Mounting Hardware

----------------------------------------------------page 13

Installing the Post Bracket Assembly -------------------------------------------page 13

Installing the Gate Bracket -------------------------------------------------------page 16

Mounting the Operator ------------------------------------------------------------page 17

Installation of the Closed Position Stop ---------------------------------------------page 18

Mounting the Control Box -------------------------------------------------------------page 20

Installing the Battery -------------------------------------------------------------------page 20

Connecting the Operator Power Cable ----------------------------------------------page 21

Powering the System --------------------------------------------------------------

page 22

Solar Chart -------------------------------------------------------------------------------page 22

Connecting the Transformer -----------------------------------------------------------page 23

Control Board Settings ----------------------------------------------------------

page 25

DIP Switches ----------------------------------------------------------------------------page 25

Setting the Closed Position ------------------------------------------------------------page 26

Setting Your Personal Transmitter Code -------------------------------------

page 27

Obstruction Sensitivity ------------------------------------------------------------

page 28

Installing the Receiver -----------------------------------------------------------

page 28

Connecting Accessories ----------------------------------------------------------

page 29

Input Connections ----------------------------------------------------------------------page 29

Wiring Accessories ---------------------------------------------------------------------page 30

Push to Open Installation --------------------------------------------------------

page 31

Setting the Open Position Limit ------------------------------------------------------page 32

Troubleshooting Guide -----------------------------------------------------------

page 34

Repair Service ---------------------------------------------------------------------

page 37

Column Installation Information ----------------------------------------------

page 38

Accessory Catalog ----------------------------------------------------------------

page 39

Table of Contents

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

Содержание SW-4000XL













































Результаты поиска

Содержание SW-4000XL

Отзывы:

Бренды по названию

Популярные бренды

GTO SW-4000XL, Руководство по установке

Результаты поиска

Содержание SW-4000XL

Отзывы:

Бренды по названию

Популярные бренды