GSi VersaLoop Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 52

GSi VersaLoop Скачать руководство пользователя страница 34

Chapter 6: Maintenance and Troubleshooting

Gearbox

• Inspect regularly for any external damage.

• Inspect annually for any oil leakage.

• Inspect/change the oil every 1,000 hours or three years, which ever comes first.

Chain and Paddles

• Check for proper chain tension.

• The chain has connecting links spaced every 10 ft. Make sure that they are securely fastened and

the cotter pins are bent back correctly.

• Check the locknuts used to fasten the paddles to the chain brackets. They should be tightened to a

torque of 20 ft. lbs. (26 N-m).

• Spray a light coating of oil on the chain after a season of use.

VersaLoop™ – Cleanout Process

1. To clean the dust in the drive and non-drive ends, shut down the VersaLoop ™system.

2. Remove the covers from the drive end non-drive end.

3. Clean the dust from the drive and the non-drive ends.

4. Re-install the end covers.

Figure 6-1

Removing the end covers

A

End Covers

34

Pneg-1966

VersaLoop™

«
...
32
33
34
35
36
...
»

Содержание VersaLoop





















































Отзывы:

Нет отзывов