GSi VersaLoop Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 52

GSi VersaLoop Скачать руководство пользователя страница 25

Chapter 4: Assembly

NOTE:

It is possible for the chain to twist a full 360° during this process. Visually check the chain

through open covers at both the ends to make sure that this has not happened.

4. Loosen the adjusting screws in the drive end all the way (towards the tube) and connect the final

chain link.

5. Tighten the chain by turning the adjusting screws clockwise; adjust each side equally to keep the

sprocket shaft square with the housing.

6. Remove chain links if there is not enough travel in the adjusting screw to tighten the chain.

7. Make sure that the sprocket shaft is square to the housing by measuring the shaft position on both

sides of the housing.

8. The chain should be tightened until the paddles are nearly rigid on the chain. The tips of the paddles

should only move 3/4" when grabbed and pulled by hand.

9. Check and re-tension the chain as needed after the system has been trial run while empty. (Refer to

VersaLoop™ Chain – Adjustment, page 35

.)

Figure 4-8

Chain and paddle assembly

A

Chain

F

Paddle attachment bracket

B

Paddle

G

3/4 in.

C

5/16 - 18 x 1 in. flange bolt

H

0.313 in.

D

5/16 flat washer

I

Cotter pin

E

5/16 - 18 Stover nut

J

Sprocket clearance slot in paddle

Pneg-1966

VersaLoop™

25

«
...
23
24
25
26
27
...
»

Содержание VersaLoop





















































Отзывы:

Нет отзывов