Grunbeck softliQ:SC Скачать руководство пользователя страница 57

Страница: 57 / 76

Troubleshooting

57 | 76

BA_TD

0en

_07

4_sof

tli

-S

.docx

Display

Explanation

Remedy

Regeneration water meter

defective!

Regeneration water
meter is not emitting
pulses.

Connecting cable
defective.

Water supply
interrupted.

Check water supply.

Notify Grünbeck's technical service/
authorised service company.

System is not drawing brine

from the brine tank effectively

enough!

Minimum contact during
salting not reached.
Monitoring time
exceeded.

Injector clogged or raw
water pressure too low.

Notify Grünbeck's technical service/
authorised service company.

Nominal flow rate exceeded!

Only displayed if
monitoring was
activated by the
specialist installer.

System is being
operated with excessive
flow rates.

Reduce peak flow.

If the error persists, notify Grünbeck's
technical service/ authorised service
company.

9.2

Other observations

Observation

Meaning

Remedy

No soft water

Excessive water
consumption
(water softener has
exceeded its capacity).

Restrict your water consumption to
the maximum flow rate permitted
(refer to chapter 12).

Perform a manual regeneration (refer
to chapter 7.2).

Water softener does not
have a permanent
power connection.

Check the mains connection.

Soft water meter is not
emitting pulses.

Notify Grünbeck's technical service/
authorised service company.

Raw water hardness set
too low.

Measure the raw water hardness
(refer to chapter 7.4).

Check the value in the control unit
(refer to chapter 7.6).

Incorrect setting of
blending valve

Readjust the blending valve
(refer to chapter 7.7).

Содержание softliQ:SC













































































Результаты поиска

Содержание softliQ:SC

Отзывы:

Похожие инструкции для softliQ:SC

Бренды по названию

Популярные бренды

Grunbeck softliQ:SC, Руководство по эксплуатации

Результаты поиска

Содержание softliQ:SC

Отзывы:

Похожие инструкции для softliQ:SC

Бренды по названию

Популярные бренды