Grunbeck softliQ:SC Скачать руководство пользователя страница 10

Страница: 10 / 76

Safety

10 | 76

BA_TD

0en

_07

4_sof

tli

-S

.docx

2.5

Responsibilities of the owner/user

Comply with the following instructions to ensure the proper and safe functioning of the
product:

● Arrange for a specialist installer to carry out installation, start-up and maintenance.

● Have the product explained to you by the specialist installer.

● Only perform activities described in this manual.

● Do not carry out any activities that are explicitly marked for a specialist installer.

● Only use this product as intended.

● Make sure that the required inspection and maintenance work is carried out.

● Keep this manual.

2.6

Admissible regenerant

The softliQ:SC water softener may only be operated with the following regenerant:

● Salt tablets according to EN 973 type A

Other regenerants are not allowed.

Содержание softliQ:SC













































































Результаты поиска

Содержание softliQ:SC

Отзывы:

Похожие инструкции для softliQ:SC

Бренды по названию

Популярные бренды

Grunbeck softliQ:SC, Руководство по эксплуатации

Результаты поиска

Содержание softliQ:SC

Отзывы:

Похожие инструкции для softliQ:SC

Бренды по названию

Популярные бренды