Grizzly T1243 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 28

Grizzly T1243 Скачать руководство пользователя страница 8

-6-

Model T1243 (Mfd. Since 02/18)

SECTION 2: SETUP

This machine was carefully packaged for safe
transport. When unpacking, separate all enclosed
items from packaging materials and inspect them
for shipping damage.

If items are damaged,

please call us immediately at (570) 546-9663.

IMPORTANT: Save all packaging materials until
you are completely satisfied with the machine and
have resolved any issues between Grizzly or the
shipping agent. You MUST have the original pack-
aging to file a freight claim. It is also extremely
helpful if you need to return your machine later.

Unpacking

SUFFOCATION HAZARD!

Keep children and pets away

from plastic bags or packing

materials shipped with this

machine. Discard immediately.

The following items are needed, but not included,
for the setup/assembly of this machine.

Description Qty
•

Safety Glasses ........................................... 1

•

Screwdriver Flat Head #2 ........................... 1

Needed for Setup

Inventory

The following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.

If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.

Box 1 (Figure 2)

Qty

A. Cross-Slide Rotary Table (Not Shown) ...... 1

B. Hold-Down Clamps .................................... 3

C. T-Bolts ........................................................ 3

D. Handwheel Handle ..................................... 1

E. Shoulder Screw .......................................... 1

F. Fixed Handles 58mm ................................. 2

G. Fixed Handles 38mm ................................. 2

H. Flat Washers 10mm ................................... 3

I. Hex Nuts M10-1.5 ....................................... 3

Figure 2. T1243 inventory.

B

C

D

E

F

G

H

I

NOTICE

If you cannot find an item on this list, care-

fully check around/inside the machine and

packaging materials. Often, these items get

lost in packaging materials while unpack-

ing or they are pre-installed at the factory.

«
...
6
7
8
9
10
...
»

Содержание T1243





























Отзывы:

Нет отзывов