Grizzly T1243 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 28

Grizzly T1243 Скачать руководство пользователя страница 20

-18-

Model T1243 (Mfd. Since 02/18)

To lubricate Y-axis leadscrew:

1. Turn Y-axis handwheel to expose Y-axis

leadscrew cover (see

Figure 34).

Leadscrews

Oil Type .... Grizzly T26685 or ISO 32 Equivalent
Oil Amount .......................................... Thin Layer
Lubrication Frequency .............................Monthly

Lubricate the X- and Y-axis leadscrews monthly,
or more often under heavy use.

2. Tip cross-rotary table up to expose leadscrew

(see

Figure 33).

3. With stiff brush and mineral spirits, clean

debris from leadscrew. Wipe clean with shop
rag and allow to dry.

4. Coat leadscrew with thin layer of ISO 32 or

equivalent oil.

5. Tip cross-rotary table back onto base, then

use X-axis handwheel to move table along
full length of travel to spread lubricant evenly
along leadscrew.

Items Needed

Qty

Mineral Spirits .................................... As Needed
Stiff-Bristled Brush ............................................ 1
Shop Rags ......................................... As Needed

To lubricate X-axis leadscrew:

1. Turn rotary table handwheel until X-axis

handwheel is parallel with front mounting
slot, as shown in

Figure 32, then use X-axis

handwheel to move table all the way forward
over front mounting slot.

Figure 33. X-axis leadscrew exposed for

cleaning and lubrication.

X-Axis

Leadscrew

Figure 32. Aligning table to lubricate X-axis

leadscrew.

Rotary Table

Handwheel

X-Axis

Handwheel

Note:

Because the T1243 table can rotate

360°, whichever handwheel aligns with the
front mounting slot controls X-axis table
travel. To access the X-axis leadscrew for
lubrication, align the handwheels as shown in

Figure 32.

Front

Mounting

Slot

Y-Axis

Handwheel

Figure 34. Location of Y-axis leadscrew cover.

Y-Axis

Handwheel

Table

X-Axis

Handwheel

Y-Axis

Leadscrew

Cover

«
...
18
19
20
21
22
...
»

Содержание T1243





























Отзывы:

Нет отзывов