Grizzly T1243 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 28

Grizzly T1243 Скачать руководство пользователя страница 21

Model T1243 (Mfd. Since 02/18)

-19-

Adjusting Gibs

The function of the gibs is to remove play in the
table (X-axis) and cross slide (Y-axis) without
causing the slides to bind.

Each gib has (3) cap screws that can be adjusted
(see

Figure 36). The outer cap screws on each

gib have (1) hex lock nut. When adjusting, make
your adjustments equally and in small increments,
and test the feel of the table movement while
doing so until it feels right.

Tools Needed

Qty

Hex Wrench 5mm .............................................. 1
Wrench Open-End 10mm .................................. 1

To adjust gibs:

1. Loosen lock nuts under outer gib screws on

X-axis or Y-axis gib (see

Figure 36).

Note: For best performance, adjust only one
gib at a time.

2. Depending on current table movement, slight-

ly loosen or tighten each gib screw in equal
amounts, then move table with handwheels
and test feel. When properly adjusted, gibs
should offer slight resistance without binding.

3. Hold gib screw position with hex wrench, then

tighten lock nut. Repeat on all gib screws.

2. Push cover under cross slide to expose

Y-axis leadscrew (see

Figure 35).

5. When finished, use Y-axis handwheel to

move table along full length of travel to
spread lubricant evenly along leadscrew.

Note: Y-axis leadscrew cover will close auto-
matically when cross slide moves over it.

3. With stiff brush and mineral spirits, clean

debris from leadscrew. Wipe clean with shop
rag and allow to dry.

4. Coat leadscrew with thin layer of ISO 32 or

equivalent oil.

Figure 36. Gib screws and lock nuts.

X-Axis Gib

Screws

Gib Lock Nuts

Y-Axis Gib

Screws

Figure 35. Y-axis leadscrew exposed for

cleaning and lubrication.

Y-Axis

Leadscrew

Cover

«
...
19
20
21
22
23
...
»

Содержание T1243





























Отзывы:

Нет отзывов