Grizzly T1243 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 28

Grizzly T1243 Скачать руководство пользователя страница 11

Model T1243 (Mfd. Since 02/18)

-9-

Adjusting Indexing

Scale

Adjusting Handwheel

Scale

The degree scale is marked on the edge of the
rotary table in 1° increments (see

Figure 9). The

zero point can be synchronized with the handwheel
to start the table indexing at 0° by using the index
marker as a starting point.

The index marker position for the rotary table can
be adjusted /-2.5° by loosening the thumb-
screw and moving the marker.

The rotary table scale collar is marked in whole
degrees and has a resolution of 1 arc second (

1

⁄

60

of 1°). For every full rotation of the handwheel, the
indexing scale on the rotary table moves 4°.

The handwheel scale (see

Figure 7) can be

repositioned without rotating the handwheel. This
helps when aligning all of the zeroes at the
beginning of a job.

Figure 8. Location of collar set screw.

Set

Screw

Items Needed

Qty

Hex Wrench 3mm .............................................. 1

1. To adjust collar, loosen set screw (see

Figure 8) securing collar to handwheel, then
rotate collar to desired alignment.

Mounting Table

Horizontally

The T1243 comes with (3) M10-1.5 x 60 T-bolts,
(3) M10-1.5 hex nuts, (3) 10mm flat washers, and
(3) hold-down clamps for mounting horizontally to
a milling machine table. Use the supplied hard-
ware to mount the T1243 to milling machine tables
with spacing up to 4" on center between

7

⁄

16

" or

1

⁄

2

"

T-slots.

Figure 7. Rotary table scale collar index.

Rotary Table

Scale Collar

2. When finished, tighten set screw to secure

collar.

Figure 9. Location of degree scale.

Degree

Scale

Index

Marker

Thumbscrew

To mount the T1243 to tables with T-slots

spaced wider than 4" on center, or with

T-slots wider than

1

⁄

2

", use step blocks and

clamps (available separately).

«
...
9
10
11
12
13
...
»

Содержание T1243





























Отзывы:

Нет отзывов