Grizzly G0899 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 92

Grizzly G0899 Скачать руководство пользователя страница 43

Model G0899 (Mfd. Since 10/20)

-41-

Blade Tilt/Bevel Cuts

When the blade tilt collar bolts are properly adjust-
ed (as described starting on

Page 65), the blade

tilt handwheel allows the operator to tilt the blade
to the left, between 0° and 45°. This is used most
often when cutting bevels, compound miters, or
chamfers.

Figure 63 shows an example of the

blade when tilted to 45°.

Figure 63. Example of blade tilted to 45° for

bevel cutting (blade guard only removed for

clarity.

Installing a Dado Blade

1. DISCONNECT MACHINE FROM POWER!

2. Remove table insert, blade guard assembly

or riving knife, arbor nut, flange, and saw
blade.

3. Attach and adjust dado blade system accord-

ing to dado blade manufacturer’s instruc-
tions, and secure with included dado blade
flange and arbor nut.

4. Install dado table insert.

The Model G0899 can accommodate dado blades
up to 8" in diameter. However, you MUST install
the included riving knife while using a 8" diameter
dado blade, as it provides a barrier behind the
blade and reduces the risk of hands being pulled
into the blade if kickback occurs.

DO NOT use the riving knife if you install a dado
blade smaller than 8" in diameter. Otherwise, the
riving  knife  height  will  exceed  the  blade  height
and  the  workpiece  will  hit  the  riving  knife  during
the  cut,  forcing  the  operator  into  a  dangerous
situation  and  trying  to  turn  the  saw  off  with  the
workpiece stuck halfway through the cut.

Never try to cut a warped board by hold-

ing it down against the table. If kickback

occurs, your hand could be pulled into the

blade, resulting in accidental contact with

the rotating blade, causing severe lacera-

tions or amputation.

DO NOT make through cuts with a dado

blade. The extra width of a dado blade

will increase the risk of kickback during a

through cut. Dado blades are only intended

for non-through cuts. Failure to heed this

warning could result in serious injury.

Dado Cutting

Figure 64. Example of a dado being cut with a

dado blade.

Commonly used in furniture joinery, a dado is a

straight channel cut in the face of the workpiece.
Dadoes are "non-through" cuts that can be made
with a dado blade or a standard saw blade. The

Figure below shows a cutaway view of a dado cut
being made with a dado blade.

Dado Blade

Workpiece

Fence

«
...
41
42
43
44
45
...
»

Содержание G0899





























































































Отзывы:

Нет отзывов