manualshive.com logo in svg

Grizzly G0817, Руководство пользователя, Страница: 60 / 88

Поделиться
Скачать
Grizzly G0817 Скачать руководство пользователя страница 60

-58-

Model G0817 (Mfd. Since 05/16)

Operating Machine (Continued)

Symptom

Possible Cause

Possible Solution

Gullets loaded with 
chips.

1.  Excessive feed rate/pressure.
2.  Blade TPI is too fine.

1.  Reduce feed rate/pressure.
2.  Install correct blade (

Page 41).

Backside of blade 
deformation/
cracking.

1. 

Excessive feed rate/pressure.

2.  Blade tension too high.
3.  Blade support bearing improperly adjusted.

1.  Reduce feed rate/pressure.
2.  Adjust blade tension (

Page 28).

3.  Properly adjust blade support bearing (

Page 31).

Sawdust buildup 
inside cabinet.

1.  Blade brushes under table are worn or mis-

adjusted.

2.  Clogged dust port.
3.  Low CFM (airflow) from dust collection 

system.

1.  Properly adjust brushes; replace if necessary 

(

Page 62).

2.  Clean dust port.
3.  Inspect ducting for leaks/clogs and repair as 

necessary; move dust collector closer to machine; 
install a stronger dust collector.

Содержание G0817

























































































Отзывы:

Нет отзывов