Grizzly G0817 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 88

Grizzly G0817 Скачать руководство пользователя страница 28

-26-

Model G0817 (Mfd. Since 05/16)

To adjust blade tracking:

1. DISCONNECT MACHINE FROM POWER!

2. Adjust upper and lower blade guides away

from blade, and raise upper guides approxi-
mately

2

⁄

3

of the way up (refer to

Adjusting

Blade Guide Bearings on Page 32 for
detailed instructions).

Note: When adjusting the blade tracking for
the test run in this procedure, the blade must
have approximately the same amount of ten-
sion as when under operating conditions.
After the test run is successfully completed,
you will be instructed on how to more accu-
rately tension the blade for optimum results.

3. Move blade tension quick-release lever down

to apply tension to blade (see

Figure 37).

Figure 37. Blade tension quick-release lever in

down position, applying tension to blade.

Blade Tension

Quick-Release

Lever

4. Open upper wheel cover (see Figure 38).

5. Rotate blade tension handwheel until ten-

sion scale (see

Figure 38) is between 4 and

6. Rotate handwheel clockwise to increase
blade tension. Rotate handwheel counter-
clockwise to decrease blade tension.

Figure 38. Blade tensioning controls.

Blade Tension

Scale

Blade Tension

Handwheel

6. Loosen tracking control lock lever on back of

bandsaw (see

Figure 39).

7. Rotate upper wheel by hand several times

and watch how blade rides on wheel (see

Figure 39).

— If the blade consistently rides in the center

of the upper wheel, it is tracking properly
and no adjustments are necessary; pro-
ceed to

Step 9.

— If the blade does not consistently ride in

the center of the upper wheel, it is not
tracking properly; proceed to

Step 8.

Figure 39. Blade tracking controls.

Blade

Tracking

Window

Blade

Wheel

Tracking

Control

Knob

Tracking

Control

Lock

Lever

8. Adjust tracking control knob (see Figure 39

on

Page This Page) in small amounts and

continue to rotate upper wheel by hand at the
same time until blade consistently rides in
center of bandsaw tire.

9. Tighten tracking control lock lever, and close

and secure upper wheel cover.

Note:

For the best performance from your

saw, regularly maintain proper tracking of the
blade. Fine tune tracking must be done with
the bandsaw turned

ON. Refer to Page 30 for

more information.

«
...
26
27
28
29
30
...
»

Содержание G0817

























































































Отзывы:

Нет отзывов