Grizzly G0817 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 88

Grizzly G0817 Скачать руководство пользователя страница 33

Model G0817 (Mfd. Since 05/16)

-31-

Adjusting Blade

Support Bearings

The  support  bearings  are  positioned  behind  the
blade near the blade guides and prevent the blade
from pushing backward during cutting operations.
Proper adjustment of the support bearings helps
you  make  accurate  cuts  and  prevents  the  blade
teeth from coming in contact with the blade guides
while  cutting.  If  this  happens,  the  blade  "tooth
set" can be ruined, which will greatly reduce the
blade's ability to make good cuts.

There are support bearings on the upper and
lower blade guide assemblies. Both adjust in the
same manner. The following instructions refer to
the upper support bearings.

Important: To ensure best results while cutting,
make sure the blade is tracking and tensioned
correctly before performing this procedure.

Tools Needed

Qty

Hex Wrench 5mm .............................................. 1

To adjust support bearing:

1. DISCONNECT MACHINE FROM POWER!

2. Loosen support bearing adjustment screw

(see

Figure 44).

Figure 44. Upper support bearing assembly and

controls (guide post cover removed for clarity).

Support Bearing

Support Bearing

Adjustment Screw

3. Position support bearing approximately

0.016" away from back of blade, as illustrated
in

Figure 45.

Note: The main purpose of this adjustment
is to prevent the blade from being pushed
backward far enough that the blade guides
will contact (and ruin) the "tooth set" of the
blade during cutting operations.

0.016''

Figure 45. Bearing positioned approximately

0.016" away from back of blade.

4. Tighten adjustment cap screw to lock support

bearing in place.

«
...
31
32
33
34
35
...
»

Содержание G0817

























































































Отзывы:

Нет отзывов