Grizzly G0817 Скачать руководство пользователя страница 24

Страница: 24 / 88

-22-

Model G0817 (Mfd. Since 05/16)

4. Secure table to trunnion using (4) M8-1.25 x

25 hex bolts, (4) 8mm lock washers, and (4)
8mm flat washers (see

Figure 26).

5. Install table insert (see Figure 27).

6. Install table gap screw assembly, secure with

(1) M8-1.25 hex nut and (1) 8mm flat washer
(see

Figure 27), then tighten gap screw to

ensure table surface is flush across gap.

Figure 26. Table to trunnion mounting hardware

installed.

x 4

Figure 27. Table insert and gap screw installed.

Table Insert

Gap Screw

Assembly

Hex Nut

and Washer

8. Install fence rail using (2) M6-1 x 20 hex

bolts, (2) 6mm lock washers, and (2) 6mm flat
washers (see

Figure 29).

Fence Rail

x 2

Figure 29. Installing fence rail.

9. Thread (1) M8-1.25 hex nut onto lock lever,

install lock lever onto fence base, then tighten
hex nut to secure (see

Figure 30).

Figure 30. Fence base lock lever installed.

Fence

Base

Hex Nut
M8-1.25

Lock

Lever

7. Install fence support using (2) M6-1 x 12 cap

screws and 6mm flat washers (see

Figure 28).

Figure 28. Installing fence support.

x 2

Fence Support

Содержание G0817

























































































Результаты поиска

Содержание G0817

Отзывы:

Grizzly G0817, Руководство пользователя, Страница: 24 / 88

Результаты поиска

Содержание G0817

Отзывы: