Grizzly G0817 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 88

Grizzly G0817 Скачать руководство пользователя страница 23

Model G0817 (Mfd. Since 05/16)

-21-

Anchoring to Floor

Anchoring machinery to the floor prevents tipping
or shifting and reduces vibration that may occur
during operation, resulting in a machine that runs
slightly quieter and feels more solid.

If the machine will be installed in a commercial or
workplace setting, or if it is permanently connect-
ed (hardwired) to the power supply, local codes
may require that it be anchored to the floor.

If not required by any local codes, fastening the
machine to the floor is an optional step. If you
choose not to do this with your machine, we rec-
ommend placing it on machine mounts, as these
provide an easy method for leveling and they have
vibration-absorbing pads.

Lag shield anchors with lag screws (see below)
are a popular way to anchor machinery to a con-
crete floor, because the anchors sit flush with the
floor surface, making it easy to unbolt and move
the machine later, if needed. However, anytime
local codes apply, you MUST follow the anchoring
methodology specified by the code.

Machine Base

Concrete

Lag Screw

Lag Shield Anchor

Flat Washer

Drilled Hole

Figure 23. Popular method for anchoring

machinery to a concrete floor.

Anchoring to Concrete Floors

Number of Mounting Holes ............................ 4

Diameter of Mounting Hardware .................

3

⁄

8

"

Assembly

To assemble bandsaw:

1. Remove protective shipping cover from blade,

then remove table insert and shipping screw
from table (see

Figure 24).

2. Place table on saw, sliding table gap around

blade (see

Figure 24).

The machine must be fully assembled before it
can be operated. Before beginning the assembly
process, refer to

Needed for Setup and gather

all listed items. To ensure the assembly process
goes smoothly, first clean any parts that are cov-
ered or coated in heavy-duty rust preventative (if
applicable).

3. Carefully position table so gap faces to the

right (see

Figure 25).

Figure 25. Table rotated with gap facing to the

right.

Blade

Table

Gap

Figure 24. Placing table on saw with gap

positioned around blade.

Table Insert

Removed

Shipping Screw

Removed

Table

Gap

«
...
21
22
23
24
25
...
»

Содержание G0817

























































































Отзывы:

Нет отзывов