Grizzly G0817 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 88

Grizzly G0817 Скачать руководство пользователя страница 22

-20-

Model G0817 (Mfd. Since 05/16)

Lifting & Placing

HEAVY LIFT!

Straining or crushing injury

may occur from improperly

lifting machine or some of

its parts. To reduce this risk,

get help from other people

and use a forklift (or other

lifting equipment) rated for

weight of this machine.

Special care should be taken when moving this
bandsaw. To reduce your risk of injury or acciden-
tal damage, use one of the following methods to
lift or move this bandsaw.

Using Forklift & Eye Bolt

1. Use forklift to move crate to prepared loca-

tion, then remove crate from shipping pallet.

2. Unbolt bandsaw from pallet.

3. Install eye bolt. Make sure it is threaded all

the way in,

then place lifting hook through eye

bolt (see

Figure 21) and lift bandsaw slowly

with forklift enough to clear pallet.

Using Forklift & Wood Blocks

1. Use forklift to move crate to prepared loca-

tion, then remove crate from shipping pallet.

2. Unbolt bandsaw from pallet.

3. Carefully place forklift forks under bandsaw

head. Insert a 1x4 block between head and
left fork, and a 2x4 block between head and
right fork so bandsaw is level, as shown in

Figure 22.

Using Pallet Jack & Furniture Dolly

1. Use pallet jack to move crate to prepared

location, then remove crate from shipping
pallet.

2. Unbolt bandsaw from pallet.

3. With help of another person, carefully "walk"

bandsaw (or use furniture dolly to move
bandsaw) off of pallet and into position.

2x4

1x4

Figure 22. Example of lifting bandsaw with

forklift using wood shims.

4. Lift bandsaw off of pallet, remove pallet, then

slowly set bandsaw into position.

Note: If you are concerned about your forklift forks
hitting the tension handwheel, remove handwheel
before positioning forks, then re-install it after
placing bandsaw in final location.

Serious injury could occur if you connect

machine to power before completing setup

process. DO NOT connect to power until

instructed later in this manual.

Figure 21. Lifting bandsaw with eye bolt and

chain.

4. Remove pallet and slowly set bandsaw into

position.

Eye Bolt

Lifting Hook

«
...
20
21
22
23
24
...
»

Содержание G0817

























































































Отзывы:

Нет отзывов