Grizzly G0817 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 88

Grizzly G0817 Скачать руководство пользователя страница 34

-32-

Model G0817 (Mfd. Since 05/16)

Adjusting Blade

Guide Bearings

The  blade  guide  bearings  can  be  adjusted  left-
to-right,  as  well  as  front-to-back,  relative  to  the
blade.  Properly  adjusted  blade  guide  bearings
provide side-to-side support, from just behind the
gullets to the back of the blade, to help keep the
blade straight while cutting.

There are blade guide bearings on the upper and
lower blade guide assemblies. Both adjust in the
same manner. The following instructions refer to
the upper guide bearings.

Important: Make sure the blade is tracking and
tensioned correctly before performing this proce-
dure (see

Tensioning Blade on Page 28).

Tools Needed

Qty

Hex Wrench 5mm .............................................. 1

To adjust blade guides:

1. DISCONNECT MACHINE FROM POWER!

2. Loosen guide block adjustment cap screw

shown in

Figure 46, then position guide bear-

ings just behind blade gullets, as illustrated
in

Figure 47. Retighten cap screw to secure

setting.

Note: The guide bearings should be posi-
tioned behind the gullets a distance equal to
that of the support bearing behind the blade
(see

Page 31).

Figure 46. Upper guide bearing components

(guide post cover removed for clarity).

Guide

Block

Guide Block

Adjustment

Cap Screw

Guide

Bearings

Blade

Guide

Bearing

Blade

Gullets

Approximately

0.016"

Figure 47. Blade guide bearing positioned just

behind blade gullets.

Note: With wider blades, it may not be possi-
ble to bring the guide bearings just behind the
blade gullets. Position them as far forward as
possible without allowing the guide bearing
housing to touch the back of the blade.

Blade teeth are angled out slightly, protrud-

ing wider than the blade thickness; this is

known as blade "tooth set" (see Figure 48).

If angled out parts of the teeth contact guide

bearings during operation, they will get bent

inward, ruining the tooth set. Therefore,

the support bearing must be set to prevent

teeth from contacting guide bearings during

operation (refer to Page 31 for details).

“Tooth Set”

Wider Than

Blade Thickness

BladeThickness

Figure 48. Illustration of blade "tooth set."

«
...
32
33
34
35
36
...
»

Содержание G0817

























































































Отзывы:

Нет отзывов