manualshive.com logo in svg

Grizzly G0812, Руководство пользователя

Поделиться
Скачать
Grizzly G0812 Скачать руководство пользователя страница 31

Model G0812 (Mfd. Since 2/16)

-29-

Blade Care

To prolong blade life, always use a blade with the 
proper width, set, type, and pitch for each appli-
cation.  Maintain  the  appropriate  feed  rate,  feed 
pressure,  and  blade  speed,  and  pay  attention  to 
the  chip  characteristics  (Refer  to 

Blade Speed 

Chart  on  Page  30  and  Chip Inspection Chart 
on 

Page 31). Keep your blades clean, since dirty 

or  gummed  up  blades  pass  through  the  cutting 
material  with  much  more  resistance  than  clean 
blades, causing unnecessary heat.

Blade Care & 

Break-In

Blade Break-In

The tips and edges of a new blade are extremely 
sharp.  Cutting  at  too  fast  of  a  feed  rate  or  too 
slow of a blade speed can fracture these tips and 
edges,  quickly  dulling  the  blade.  Properly  break-
ing in a blade allows these sharp edges to wear 
without  fracturing,  thus  keeping  the  blade  sharp 
longer. Below is a typical break in procedure. For 
aftermarket  blades,  refer  to  the  manufacturer's 
break-in  procedure  to  keep  from  voiding  the 
warranty.

Use  the 

Chip Inspection Chart on  Page  31  as 

a guide to evaluate the chips and ensure that the 
optimal blade speed and feed rate are being used.

To properly break-in new blade:

1.  Choose correct speed for blade and material 

type.

2.  Reduce feed pressure by half for first 50–100 

in

2

 of material cut.

3.  To avoid twisting blade when cutting, adjust 

feed pressure when total width of blade is in 
cut.

Model G0812 blade speeds: 95–380 FPM. 

During operation, pay attention to the chips being 
produced from the cut and compare them to the 

Chip Inspection Chart on  Page  31  to  properly 
set the downfeed rate.

Blade Speed

Entanglement Hazard! 

You MUST install the pul-

ley cover before operat-

ing or severe injury may 

occur.

To change blade speeds:

1.  Turn bandsaw ON and allow motor to reach 

full speed.

2.  Rotate speed adjustment knob (see Figure 33) 

clockwise to decrease blade speed and coun-
terclockwise to increase blade speed.

NOTICE

Only change speeds while the motor is run-

ning. Changing speeds when machine is 

OFF may result in damage to your machine. 

Always make sure belt guard is in use.

Figure 33. Speed adjustment knob location.

Speed Adjustment 

Knob

Содержание G0812





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды