Grizzly G0806 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 80

Grizzly G0806 Скачать руководство пользователя страница 27

Model G0806/G0807 (Mfd. Since 12/15)

-25-

Adjusting Blade

Guide Assemblies

The blade guide assemblies were properly adjust-
ed  at  the  factory;  however,  due  to  the  vari-
ables involved with shipping, we recommend that
you  check  the  blade  guide  assemblies.  Properly
adjusted  blade  guide  assemblies  are  essential
to  making  accurate  cuts  because  they  keep  the
blade supported during operation, which prevents
the blade from wandering.

The blade guide assemblies help to keep the blade
straight while cutting. Use

Figures 26–28 and the

following descriptions to better understand the
components of the blade guide assembly.

Blade Support

Blade

Guide

Blade Guide

Support

Cap Screw

Side

View

Blade

Guide

Bracket

Guide

Post

Blade Guide

Bracket

Cap Screw

Blade Support

Adjustment

Cap Screw

Blade

Figure 28. Upper blade guide components.

Note: Both the upper and lower blade guide
assemblies are adjusted in the same manner. To
access the lower assembly, you will need to first
remove the lower blade guards.

Blade Guides: Support the blade on both sides.

Blade Guide Bracket: Holds the blade guides.

Blade Support: Supports the blade from behind.

Blade Guide Support Cap Screws: Secure the
blade guides in the proper position on both sides
of the blade.

Blade Guide Bracket and Blade Support

Adjustment Cap Screws: Secure the position of
the blade guide brackets and the blade supports.

Figure 27. Front view of upper blade guide

assembly.

Blade Guide

Support

Cap Screw

Figure 26. Blade guide assembly components.

Blade Guide

Bracket

Blade

Support

Blade Guide
Bracket Cap

Screw

Blade Support

Adjustment Cap Screw

Blade Guide

«
...
25
26
27
28
29
...
»

Содержание G0806

















































































Отзывы:

Нет отзывов