Grizzly G0806 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 80

Grizzly G0806 Скачать руководство пользователя страница 15

Model G0806/G0807 (Mfd. Since 12/15)

-13-

G0806 Circuit Requirements for 220V

Operation

No adapter should be used with plug. If

plug does not fit available receptacle, or if

machine must be reconnected for use on a

different type of circuit, reconnection must

be performed by an electrician or qualified

service personnel, and it must comply with

all local codes and ordinances.

G0806 Circuit Requirements for 110V

Operation (Prewired)

Nominal Voltage ......... 208V, 220V, 230V, 240V

Cycle ..........................................................60 Hz

Phase ........................................... Single-Phase

Power Supply Circuit ......................... 15 Amps

Plug/Receptacle ............................. NEMA 6-15

This  machine  can  be  converted  to  operate  on  a
power  supply  circuit  that  has  a  verified  ground
and  meets  the  requirements  listed  below.  (Refer
to

Voltage Conversion instructions for details.)

For 220V operation:  The  plug  specified  under
“Circuit  Requirements  for  220V”  on  the  previous
page has a grounding prong that must be attached
to the equipment-grounding wire on the included
power cord. The plug must only be inserted into
a  matching  receptacle  (see  following  figure)  that
is properly installed and grounded in accordance
with all local codes and ordinances.

Figure 5. Typical 6-15 plug and receptacle.

Grounding Prong

Current Carrying Prongs

6-15 PLUG

GROUNDED

6-15 RECEPTACLE

This machine is equipped with a power cord that
has an equipment-grounding wire and a grounding
plug. Only insert plug into a matching receptacle
(outlet) that is properly installed and grounded in
accordance with all local codes and ordinances.
DO NOT modify the provided plug!

Figure 4. Typical 5-15 plug and receptacle.

Grounding Prong

Neutral Hot

5-15 PLUG

GROUNDED

5-15 RECEPTACLE

Nominal Voltage .................... 110V, 115V, 120V

Cycle ..........................................................60 Hz

Phase ........................................... Single-Phase

Power Supply Circuit ......................... 20 Amps

Plug/Receptacle ............................. NEMA 5-15

SHOCK HAZARD!

Two-prong outlets do not meet the grounding

requirements for this machine. Do not modify

or use an adapter on the plug provided—if

it will not fit the outlet, have a qualified

electrician install the proper outlet with a

verified ground.

This machine is prewired to operate on a power
supply circuit that has a verified ground and meets
the following requirements:

«
...
13
14
15
16
17
...
»

Содержание G0806

















































































Отзывы:

Нет отзывов