Grizzly G0806 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 80

Grizzly G0806 Скачать руководство пользователя страница 16

-14-

Model G0806/G0807 (Mfd. Since 12/15)

We do not recommend using an extension cord
with this machine. If you must use an extension
cord, only use it if absolutely necessary and only
on a temporary basis.

Extension cords cause voltage drop, which can
damage electrical components and shorten motor
life. Voltage drop increases as the extension cord
size gets longer and the gauge size gets smaller
(higher gauge numbers indicate smaller sizes).

Any extension cord used with this machine must
be in good condition and contain a ground wire
and matching plug/receptacle. Additionally, it must
meet the following size requirements:

Extension Cords

Minimum Gauge Size ...........................12 AWG

Maximum Length (Shorter is Better).......50 ft.

G0807 Circuit Requirements for 220V

Operation (Prewired)

G0807 Circuit Requirements for 110V

Operation

Nominal Voltage .................... 110V, 115V, 120V

Cycle ..........................................................60 Hz

Phase ........................................... Single-Phase

Power Supply Circuit ......................... 30 Amps

Plug/Receptacle ...........................NEMA L5-30

This  machine  can  be  converted  to  operate  on  a
power  supply  circuit  that  has  a  verified  ground
and  meets  the  requirements  listed  below.  (Refer
to

Voltage Conversion instructions for details.)

Nominal Voltage ......... 208V, 220V, 230V, 240V

Cycle ..........................................................60 Hz

Phase ........................................... Single-Phase

Power Supply Circuit ......................... 15 Amps

Plug/Receptacle ............................. NEMA 6-15

This machine is equipped with a power cord that
has an equipment-grounding wire and a grounding
plug. Only insert plug into a matching receptacle
(outlet) that is properly installed and grounded in
accordance with all local codes and ordinances.
DO NOT modify the provided plug!

No adapter should be used with plug. If

plug does not fit available receptacle, or if

machine must be reconnected for use on a

different type of circuit, reconnection must

be performed by an electrician or qualified

service personnel, and it must comply with

all local codes and ordinances.

Figure 6. Typical 6-15 plug and receptacle.

Grounding Prong

Current Carrying Prongs

6-15 PLUG

GROUNDED

6-15 RECEPTACLE

Figure 7. Typical L5-30 plug and receptacle.

Grounding Prong

is Hooked

Hot

Neutral

L5-30 GROUNDED

LOCKING

RECEPTACLE

L5-30

LOCKING

PLUG

This machine is prewired to operate on a power
supply circuit that has a verified ground and meets
the following requirements:

Serious injury could occur if you connect

machine to power before completing setup

process. DO NOT connect to power until

instructed later in this manual.

«
...
14
15
16
17
18
...
»

Содержание G0806

















































































Отзывы:

Нет отзывов