GreenTec Scorpion 330-4 S Скачать руководство пользователя страница 92

Страница: 92 / 95

Scorpion 4, 6 and 8

Table 8

cont....

Slow joystick
control

Dirt has entered the
joystick or moving parts
are worn

The joystick is cleaned and lubricated. If worn,
replace the worn parts in an authorized workshop

Electrically
operated valve
does not
respond

Defective distribution
system

Check the electric distribution system in an
authorized workshop

Power supply from tractor
is too low

Check the cable and battery connection on the
tractor. Check the fuse at the battery connection

Contaminants in valve

Check for contaminants/moisture/water in
an authorized workshop

Electrically
operated valve
does not respond
Electric switches
are failing.
Bad cutting
performance

Valve is stuck

Replace valve in an authorized workshop

Power supply from tractor
is too low

Check the cable and battery connection on the
tractor. Check the fuse at the battery connection

Switch exposed to water

The machine must be stored under roof or
covered up

Worn flails

Replace worn flails

Electrical
switches are
failing

Rotor speed/direction

Check tractor speed, is the rotor turning
the right way?

Driving speed too high

Drive slower

Bad cutting
performance
Rotor bearings
failing

The growth conditions

Locate suitable conditions. If possible, change to a
different flail type

Rotor out of balance

Check rotor vibrations

Wire/string in bearing

Remove wire/string

Lack of maintenance

Lubricate bearings as recommended

Rotor bearings
failing
Rotor vibrations

Water in bearing

The water is squeezed out using grease

Flails broken or missing

Replace flails

Hub worn or damaged

Replace bearing

Rotor bent

Bring rotor into balance/replace rotor

Rotor vibrations
Heavy belt wear

Clogged by waste
material

Remove waste material

Wrong speed

Check the speed of the rotor (rev/min)

Condition of belt
and belt pulley

If necessary, replace

Incorrect belt tension

Check belt tension

Straightening of belt
pulley

Check straightening

Heavy belt wear

Overloading of tool

Reduce driving speed or increase the cutting height

Table 8

– Troubleshooting

Содержание Scorpion 330-4 S
































































































Результаты поиска

Содержание Scorpion 330-4 S

Отзывы:

Похожие инструкции для Scorpion 330-4 S

Бренды по названию

Популярные бренды

GreenTec Scorpion 330-4 S, Руководство пользователя

Результаты поиска

Содержание Scorpion 330-4 S

Отзывы:

Похожие инструкции для Scorpion 330-4 S

Бренды по названию

Популярные бренды