GreenTec Scorpion 330-4 S Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 95

GreenTec Scorpion 330-4 S Скачать руководство пользователя страница 14

14

Scorpion 4, 6 and 8

Safety labelling

The machine is affixed with safety labels, these are placed at the identified dangers
that the user is exposed to while working with or being near the machine.

Labels

Warning

Before carrying out any
maintenance or repairs on
the machine: Switch off the
engine, remove the ignition
key and pull the handbrake.

Warning

Read the instructions
manual carefully before
using this machine. Follow
all instructions and safety
precautions when using the
machine.

Warning

Rotating power take-off
shaft (PTO). Before
operating:
Switch off the engine,
remove the ignition key and
pull the handbrake.

Warning

Check every 8 hours that all
bolts / nuts are tightened.

Warning

There is a danger of getting
crushed or hit when the
machine is running.

No one is allowed in the
work zone.

Warning

Oil under high pressure -
Be careful to avoid skin
contact / inhalation of
fumes when handling - or in
case of a leak.

Warning

Always be aware of
overhead lines. There will
always be a risk of
touching the overhead
lines. In case of doubt -
contact the local power
plant for instructions on

safety distances.

Warning

There is a danger of getting
crushed when the machine
is mounted on the vehicle.
No one is allowed between
the vehicle and the tool.

Figure 5 -

Safety labelling Warning Signs

«
...
12
13
14
15
16
...
»

Содержание Scorpion 330-4 S
































































































Отзывы:

Нет отзывов