GREAT PLAINS Yield-Pro YP4025A-48TR20 Скачать руководство пользователя страница 110

Страница: 110 / 190

2019-03-19

Table of Contents

Index

411-198M

YP4025A-48TR20

Table of Contents

Index

106

Maintenance and Lubrication

Maintenance

Proper servicing and maintenance is the key to long

implement life. With careful and systematic inspection,

you can avoid costly maintenance, downtime, and repair.
Always turn off and remove the tractor key before

making any adjustments or performing any maintenance.

Crushing Hazard:

Always have transport locks in place and frame sufficiently

blocked up when working on implement. You may be severely
injured or killed by being crushed under the falling implement.

High Pressure Fluid Hazard:

Check all hydraulic lines and fittings before applying pressure.

Fluid escaping from a very small hole can be almost invisible.
Use paper or cardboard, not body parts, and wear heavy

gloves to check for suspected leaks. Escaping fluid under

pressure can have sufficient pressure to penetrate the skin. If
an accident occurs, seek immediate medical assistance from a

physician familiar with this type of injury.

1. After using your product for several hours, check all

bolts to be sure they are tight.

2. Remove excess slack from chains. Clean and use

chain lube on all roller chains as needed.

3. Maintain proper air pressure in product tires.
4. Keep disc scrapers properly adjusted.
5. Clean product on a regular basis. Regular and

thorough cleaning will lengthen equipment life and

reduce maintenance and repair.

6. Lubricate areas listed under “

Lubrication

” on

page 125.

7. Replace any worn, damaged, or illegible safety

labels by obtaining new labels from your Great

Plains dealer.

Содержание Yield-Pro YP4025A-48TR20































































































































































































Результаты поиска

Содержание Yield-Pro YP4025A-48TR20

Отзывы:

Похожие инструкции для Yield-Pro YP4025A-48TR20

Бренды по названию

Популярные бренды

GREAT PLAINS Yield-Pro YP4025A-48TR20, Руководство оператора

Результаты поиска

Содержание Yield-Pro YP4025A-48TR20

Отзывы:

Похожие инструкции для Yield-Pro YP4025A-48TR20

Бренды по названию

Популярные бренды