GREAT PLAINS Yield-Pro YP4025A-48TR20 Скачать руководство пользователя страница 124

Страница: 124 / 190

2019-03-19

Table of Contents

Index

411-198M

YP4025A-48TR20

Table of Contents

Index

Maintenance and Lubrication

120

Wing Alignment

To check and adjust wing alignment:
1. Unfold product. See “

Unfolding the Product

” on

page 26.

2. Set tongue height (page 23).

Lower product. Pull forward.

Refer to Figure 135 and Figure 136

3. Select a common reference point that is easy to

access at the wing-end and center section end row

units, such as the back of the press wheel

assembly

. On a twin-row product, align using only

the rear units.

4. Check for proper alignment by running a string line

across back of product toward outer ends of wings.

For proper alignment, outside ends of wings

should be 0-to-

inch (0-to-6 mm) ahead of inside

ends of wings at center section .

5. To adjust wing alignment, shorten or lengthen eye

bolts to change the length of the wing pull bar.
Adjust eye bolts in or out until dimension is 0 to

inch (0-to-6.4 mm) greater than dimension .

6. Be sure both wings are adjusted equally or the

product will tend to pull sideways behind the tractor.

Measure length of both pull bars, pin to pin, and set

the same.

Figure 135

Alignment Reference Point

29600

Figure 136

Wing Alignment

29270

Содержание Yield-Pro YP4025A-48TR20































































































































































































Результаты поиска

Содержание Yield-Pro YP4025A-48TR20

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS Yield-Pro YP4025A-48TR20, Руководство оператора

Результаты поиска

Содержание Yield-Pro YP4025A-48TR20

Отзывы:

Бренды по названию

Популярные бренды