GREAT PLAINS Yield-Pro YP4025A-48TR20 Скачать руководство пользователя страница 79

Страница: 79 / 190

YP4025A-48TR20

Table of Contents

Index

Adjustments

2019-03-19

Table of Contents

Index

411-198M

Liquid Fertilizer Adjustments

Liquid fertilizer distribution systems

are optional on the

implement name and are optimized for use with the

optional on-board 2x200 gallon tanks and/or the Great

Plains SML-500 or SML-735 tank carts.
If installed, there are several points of fertilizer setup

and/or adjustment:
1. Row orifice setup

Orifice plate sizes are chosen to assure consistent

pressure at all nozzles. Refer to the Seed Rate

manual.

2. Relief valve setting

See “

Fertilizer Relief Valve

” on page 76.

3. Inlets

Both Type 2 (1-section, single inlet) and Type 3

(3-section, 3-inlet) systems have quick-connect

inlets and shutoff valves at the back of the product.

See page 22 for hook-up details.

4. Strainer setup

The optional ground drive pump includes a strainer.

The mesh screen size must be compatible with the

orifice plates in the distribution system. Refer to the

Seed Rate manual.

5. Seed monitor control channel adjustment.

Once the control channel is set up, rate adjustment,

and channel enable/disable, are operations

performed using the seed monitor screen. The Seed

Rate manual for details.

Great Plains recommends checking with your local

agronomist as soil conditions vary. Soil conditions in your

area may need less or more fertilizer than represented in

these charts. In furrow, do not exceed 12 gallons per

acre in any case.
The liquid fertilizer system is designed to operate

(ideally) between 15 and 40 psi, but in no case more

than 65 psi. Several system elements affect system

pressure, and need initial setup, periodic maintenance,

and adjustment when changing fertilizer rates.

a. Type 2, Type 3, or both, with or without product-mounted ground drive pumps for Type 2. See page 22 for details.

Agricultural Chemical Hazards:

Avoid contact with skin or eyes. Wear proper protective

equipment as required by chemical manufacturer. Avoid

prolonged breathing of chemical fumes. Wear respirator as
required by chemical manufacturer.Some chemicals will cause

serious burns, lung damage, and death. Seek medical

assistance immediately if accident occurs. Know what to do in
case of accident.

Содержание Yield-Pro YP4025A-48TR20































































































































































































Результаты поиска

Содержание Yield-Pro YP4025A-48TR20

Отзывы:

Похожие инструкции для Yield-Pro YP4025A-48TR20

Бренды по названию

Популярные бренды

GREAT PLAINS Yield-Pro YP4025A-48TR20, Руководство оператора

Результаты поиска

Содержание Yield-Pro YP4025A-48TR20

Отзывы:

Похожие инструкции для Yield-Pro YP4025A-48TR20

Бренды по названию

Популярные бренды