GREAT PLAINS Yield-Pro YP4025A-48TR20 Скачать руководство пользователя страница 45

Страница: 45 / 190

YP4025A-48TR20

Table of Contents

Index

Operating Instructions

2019-03-19

Table of Contents

Index

411-198M

Changing the Bulk Box or Hopper



The Product # product accepts the Great Plains

82 bu. hopper,150 bu.

hopper, or bulk seed boxes

that meet the PROBOX

®b

specification.

Tipping and Overload Hazard:

Place or remove a hopper only when empty. A full hopper can
weigh between 5000 and 10,000 lbs (2700 and 4500 kg),

which is above the lifting and balance capability of most

tractors and farm forklifts.

1. Move the product to an area of level ground and

sufficient room to maneuver a tractor or fork-loader.

2. Unhitch tank cart if present.

Refer to Figure 39

3. Disconnect hopper level sensor (if installed).
4. Remove the pin

securing the left end of the

walkboard to the ladder assembly.

5. Swing the walkboard open, and secure it at full open

with the keeper

6. Raise the product. This causes the rear transport

wheels to move forward, providing closer access for

the lifter.

7. Back up the product about three feet (1 m). This

causes the rear transport wheels to caster forward,

further reducing the reach required for lifting.

8. Turn off the seed box fan.
9. Put the towing tractor in Park. Shut off engine.

Remove key.

10. Close the slide gate at the base of the hopper or

seed box.

Refer to Figure 40

11. Remove the two pins

, at opposite corners, used to

retain the seed box or hopper. Remove these pins

even if no container is presently mounted.

Refer to Figure 41 (depicting identical process on

YP24)

12. Align the lifting forks with the slots in the rear of the

seed box or hopper. Slowly drive forward until the

forks are completely under the container.

13. Slowly lift the seed container above the bracket, and

back away from the product.

14. Lower the container to the ground for exchange with

the next seed container.

a. The 150 bu. hopper is incompatible with on-board fertilizer tanks.
b. PROBOX

is a registered trademark of Pioneer Hi-Bred International, Inc.

Figure 39

Walkboard Pin and Keeper

29312

Figure 40

Seed Box Lock Pins

29267

Figure 41

Removing/Mounting Hopper

26121

Содержание Yield-Pro YP4025A-48TR20































































































































































































Результаты поиска

Содержание Yield-Pro YP4025A-48TR20

Отзывы:

Похожие инструкции для Yield-Pro YP4025A-48TR20

Бренды по названию

Популярные бренды

GREAT PLAINS Yield-Pro YP4025A-48TR20, Руководство оператора

Результаты поиска

Содержание Yield-Pro YP4025A-48TR20

Отзывы:

Похожие инструкции для Yield-Pro YP4025A-48TR20

Бренды по названию

Популярные бренды