GRAUPNER MX-16S Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 116

background image

27

Description of transmitter – Servo display

Servo display

Pressing the

SELECT

button at the transmitter’s basic

display calls up a visual representation of the current
servo positions on the transmitter screen.

This display shows the current position of every ser-
vo in the form of a bar diagram, taking into account the
transmitter control and servo settings, the Dual Rate /
Expo functions, the inter-action of all active mixers etc.
The display is accurate, and covers the range -150% to
+150% of normal travel. 0% means the exact centre po-
sition. This allows you to check your settings quickly wi-
thout even having to switch the receiver on. However,
this does not mean that you don’t need to bother che-
cking all the programming steps on the model; you must
do this carefully before operating it for the fi rst time, as
this is the only reliable method of picking up and correc-
ting errors.

For fi xed-wing model aircraft the display shows the
information arranged in the following way:

  Bar 1 = Throttle / brake servo
  Bar 2 = Aileron or left aileron
  Bar 3 = Elevator
  Bar 4 = Rudder
  Bar 5 = Right aileron
  Bar 6 = Left camber-changing fl ap / free channel
  Bar 7 = Right camber-changing fl ap / free channel
  Bar 8 = Free channel

… and for model helicopters:

Bar 1 = Collective pitch or roll (2) or nick (2)

servo

  Bar 2 = Roll (1) servo
  Bar 3 = Nick (1) servo
  Bar 4 = Tail rotor servo (gyro)
  Bar 5 = Nick (2) servo / free channel
  Bar 6 = Throttle servo or speed controller
  Bar 7 = Gyro gain / free channel
  Bar 8 = Speed controller / free channel

Holding the

SELECT

button held in while you are at the

transmitter’s basic display calls up a visual display of the
current positions of the two INC / DEC buttons (CTRL
5 + 6). This display disappears again when you release
the

SELECT

button. At the same time a small symbol

appears on the left, adjacent to the channel display:

When you hold the

SELECT

button pressed in, the po-

sition display on the basic transmitter display, consisting
of the two central vertical bars, also changes: it switches
from a display of the current trim position to the current
position of the INC / DEC buttons, CTRL 5 + 6.
As you would expect, the left-hand bar represents the
position of the INC / DEC button CTRL 6, located to the
left of the aerial base, and the right-hand bar shows the
position of CTRL 5 (however, both horizontal bars con-
tinue to show the current position of the corresponding
transmitter stick trim levers):

As soon as you release the

SELECT

button, the screen

reverts to a display of the current trim position of the
four trim levers of the two dual-axis stick units; see pic-
ture left.

Position display

INC / DEC button, CTRL 5 + 6

«
...
25
26
27
28
29
...
»

Содержание MX-16S





















































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-16S

Бренд: Panasonic Страницы: 45

Бренд: GAUGEMASTER Страницы: 2

Бренд: EasyIO Страницы: 19

Бренд: Zero 88 Страницы: 2

Бренд: Zenit Страницы: 24

Бренд: Ebyte Страницы: 38

Бренд: EBS Страницы: 30

Бренд: Zeagle Страницы: 37

Бренд: Ultraflex Страницы: 7

MicroTech II UV05

Бренд: AAF Страницы: 50

Ungo ProSecurity RS10

Бренд: Clarion Страницы: 19

Бренд: Seneca Страницы: 4

Бренд: Mäktig Страницы: 10

Бренд: SILENTRON Страницы: 20

Бренд: MacroAir Technologies Страницы: 32

Бренд: ACTi Страницы: 20

Бренд: SOARNEX Страницы: 14

Бренд: Tristan Auron Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды