GRAUPNER mx-12 Hott, Руководство по программированию

Страница: 86 / 200

86 Program description: base settings - model helicopter
timer
Two timers are shown in the basic display: one stop-
watch and one flight timer.
STARLET
#02
0:00h
stop
flt
0:00
0:00
0.0V
5.6V HoTT
M
A physical switch or a control switch - e. g. the control
switch G3 located on the throttle limiter - can be as-
signed to these two timers in the “Timers” line …
rotor direct
swashplate
right
3sv(2rol)
cut off –125% +100% 1
pitch min rear
timer 0:00 –––
… using the switch symbol at the bottom right-hand
side of the screen. The assigned switch starts both tim-
ers, and also halts the stopwatch.
The method of assigning a physical switch or a control
switch is described on page 57.
The flight timer, and the saving of telemetry data on a
memory card inserted in the card slot (see page 23)
always starts simultaneously with the stopwatch, but
continues to run even when the stopwatch is halted
(switched off). It can only be stopped by touching the
central
ESC button of the left-hand touch-key with the
stopwatch halted.
Once stopped, both timers can be reset to the initial
value by simultaneously touching the
 buttons of
the right-hand touch-key (
CLEAR
).
Switching between “count-up” and “count-down”
Count-up timer (stopwatch function)
If you assign a switch and start the stopwatch with the
initial value of “0:00”, the timer runs up until the maxi-
mum of 180 minutes and 59 seconds, then re-starts at
0:00.
Count-down timer (timer function)
In the left-hand minutes field you can select a starting
time within the range 0 to 180 minutes; in the right-hand
seconds field the range is 0 to 59 seconds. Any combi-
nation of times can also be selected.
Simultaneously pressing the
 buttons of the right-
hand touch-key (
CLEAR
) resets any settings you have
entered to “0” or “00”.
rotor direct
swashplate
right
3sv(2rol)
cut off –125% +100% 1
pitch min rear
timer 10:01 G3
Procedure
Select the desired input field using the arrow buttons 1.
 of the left or right-hand touch-key.
Touch 2.
SET
in the centre of the right-hand touch-key.
Select the required time in the highlighted minutes 3.
and seconds fields using the arrow buttons of the
right-hand touch-key.
Touch the central
4. SET button to conclude the input
process.
Switch back to the basic display by repeatedly touch-
5.
ing the central
ESC
button of the left-hand touch-key.
With the stopwatch halted, press the  buttons of
the right-hand touch-key simultaneously (
CLEAR
) to
switch the stopwatch to the “Timer” function; see top
right in the next illustration:
STARLET
#02
0:00h
stop
flt
10:01
0:00
0.0V
5.6V HoTT
M
If you now operate the assigned switch, the stopwatch
starts from the set initial value,
counting down (“Timer
function”). When the set time has elapsed, the timer
does not stop, but continues to run to allow you to read
off the time elapsed after reaching zero. To make this
clear, the over-run time is shown highlighted (black
background).
Sequence of sounds
30 sec. before zero: triple beep
single beep every two seconds
20 sec. before zero: double beep
single beep every two seconds
10 sec. before zero: single beep
single beep every second
5 sec. before zero: single beep every second at higher
rate
zero: longer beep; display switches to
inverse video
The “alarm timer” is reset by simultaneously pressing
the
 or  buttons of the right-hand touch-key
(
CLEAR
) after you have halted the timer.